I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hello,
I'm working on an application where we're implementing the nPM1300 and utilizing the fuel gauge algorithm to estimate battery life. Interestingly, the results that...
Hello,
I am attempting to connect a ST7789 to the nRF9161 and communicate with SPI. However the display is not working and I suspect it is because the gpios output the VDD...
Dear All,
When i connect the nRF5340 Audio DK to the windows PC through the USB, It will be enumerated as a USB audio device.
And then, It will act as the default audio...
Hi, I'm currently using nrf52840 MCU for product development and almost finished my project. What I want is when producing a product, I want to compare the checksum of the...
I am trying ADC readings for connecting my sensors. To better understand and see the values, I have made a simple connection with 4 10k Resistros in series, VCC on top and...
I am working on an nRF52832-based project and I am encountering an issue with achieving low sleep current. Despite setting the TX power to 0 dBm and the advertising interval...
I am thinking of using the sample source code of nRF5340 Audio to realize LE-Audio on a board created by our company.
I have written the source code of nRF5340 Audio to...
Hi, I am pretty new to programming with NRF boards and I've hit a bit of a roadblock.
I started with the BLE Event Trigger example and I have managed to retrieve BLE advertising...
HI Noridc
I am developing with nRF5340, and I need to proceed with DTM test to verify the chip in the production process.
I am currently using this routine C:\ncs\v2.6...
Hi, I'm working on a ble peripheral that uses nRF5340, NCS recently upgraded to v2.6.1, Zephyr v3.4.99. The net core is running the HCI RPMsg controller sample as it is. In...
Greetings all. I am troubleshooting an issue on my BLE sniffer setup. While I don't 'think' this is causing my actual current failure (Wireshark not detecting COM6) I wanted...
hardware:nrf5340dk
case: Bluetooth: Direction finding central/peripheral
I modified the code to change the quantization level of the I and Q data received by the receiver...
hardware:nrf5340dk
case: Bluetooth: Direction finding central/peripheral
I added CONFIG_BT_DF_VS_CONN_IQ_REPORT_16_BITS_IQ_SAMPLES=y in the direction_finding_central...
Hello Team,
Just to give you a background , I am working on a project using the NRF Connect SDK and want to run my application from external flash memory. Specifically,...
Hi,
We have a custom board, where we assigned the following pins for SPI4M instance, and the intention is to use it with 32 MHz:
SCLK = P1.15
MISO = P1.14
MOSI = P1...
