hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hello,
I am trying to flash the nRF9160 application(merge.hex) which is created after build in an external board. The external board is from fanstel - BLG840F.
Couple...
Hi,
i've been trying to implement gnss functionality on my nrf9160dk board but it didn't work since i was doing it indoors, i've been advised to use an external antenna...
hi support team,
our ncs2.6.0 demo /samples/net/udp is supporting 7002dk, the demo works for 7002dk.
however it doesn't support 52840dk with 7002ek shield,i have modified...
Hi! We have a custom board and when ordering a new version we now get Errors on two of the 18 prototypes.
After trying on another machine with another JLink one of the two...
Hey, I have been trying to get to the root of additional current draw when crypto drivers are enabled.
Without the crypto drivers enabled the current draw between two advertisements...
Hi,
We are working on our manufacturing process that involves use of the nRF9160. I need a way to programmatically get the IMEI and ICCID in order to register the device...
I'm running a nRF52 device that's built on nRF5 SDK11, and it's remaining that way now due to regulatory reasons. My application needed to be updated to support bonding, and...
I have a nRF9160DK board running asset_tracker_v2 on a nRF9160 custom board. V1.7.0 loads and boots fine but when I use V2.5.0 the boot fails as shown below. The only change...
Hello, per the product specification, I see that the nRF52832 CIAA variant requires a shunt 1.0pF capacitor and series 3.3nH inductor.
Is this recommended regardless of...
Hello,
first I would like to "set the scene".
* hardware : cutsom board
* mcu : nrf52832
* nRF5_SDK : nRF5_SDK_17.0.2_d674dde
* software : mbr + bootloader + softdevice...
I have configured NRF52840 as coordinator ,EFR1 (ENDDEVICE) and EFR2(ENDDEVICE) as end devices. These 3 devices are connected in network.EFR2(End device )continuously sending...
I would like to understand the issue of frequency offset calibration in RF signals, I have viewed the
Case ID: 309794
nwp_006.pdf
I would like to know if I can do...
Hi,
We are working on BLE MESH using nRF52840. We are trying to put nRF52840 into deep sleep mode. The deep sleep current is about 210 micro Amp. Further, the current is...
Hi,
I have a coap server/client system and when I send a provisioning request from the client I can see the server is sending the reply. But my 'on_provisioning_reply (...