hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
HI,
I am working on a application which has an requirement, that I need to read the current value if it is above threshold value then I need to turnoff the control. Here...
The executed command at connectedhomeip/examples/lighting-app/nrfconnect: west build -p -b nrf52840dongle_nrf52840
The messages i encountered:
...
/ncs/zephyr/include...
good day,
is there a way to set a gpio when in dfu mode? wanted to make GPIO 19 of nRF52832 HIGH during DFU mode because we assigned it as an enable pin.
in DFU mode,...
Hello,
I have my own custom board with nRF52832 and a NB-iot module SIM7080G that interfaces via UART.
I can easily program the device through SWD using J-Link. I am even...
Hello,
I am using flash_write_protection_set function with few low level function call for accessing extremal flash with nRF9160. And because of that I am facing one warning...
Hi,
I am programming the nRF52833 and using NCS v2.00. I have recently programmed the Peripheral Coded PHY to the board. I am using a Google Pixel 3 with nRF Connect as...
Hi,
Can we use the PPK2 kit for measuring current consumption in any other reference design board from a different
vendor which is not same as DA. The other vendor does...
Dear person in charge.
Before using PPK2 for a evaluation of current consumption, I checkd power supply vs corrent measurement by using PPK2 and 5kΩ chip resistor.
I...
Dear All,
I am building an application that needs to use NB-IOT and if that is not available then use LTE-M. I tried sending this AT Command:
AT%XSYSTEMMODE=1,1,0,2
...
When building the Matter Light Bulb sample application for the nRF52840 fails with:
/opt/nordic/ncs/toolchains/v2.1.0/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm...
What is meaning of error code 0x3004?
The following is source code of calling sd_ble_gap_tx_power_set().
int _gapTxPowerSet(const int8_t txPwr) { ret_code_t errCode;...
How do we read/write the preferred carrier lists on the SIM card with the nRF9160? Most modems provide the at+cpol command but this doesn't seem to be implemented on the ...
Hi,
We have an application where I'm trying to maximise BLE data throughput to it's absolute highest I can get. Through reading docs/researching and doing some experiments...
1. Is it possible to set MAC address from random to static for Mesh in nRF Connect SDK?
CONFIG_BT_PRIVACY =n and CONFIG_BT_SETTINGS =y seems does not change the behavior...
Hi,
I'm trying to use LPUART in interrupt mode (not async), but I can't get it to work.
I'm using the sample in NCS, which works when using async.
When I uncomment the...
