I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
Hello Nordic Team,
I have a question out of curiosity.
BEACON debug prints has been enabled. And I am seeing these prints for every 10 seconds.
Below is the log
<t...
for the NRF9160 I have 256KB for RAM
however, only 128KB are available for my software, since it's defined as nr9160ns
how can I assign the full 256 kB for my software...
I use Nordic BLE Mesh example(Light Switch), I want to implement remote control. The following is the topology map, and the publish & subscribe address(Group address) has...
Using a NRF9160DK. SDK2.0.0. Modem 1.3.2.
I have a problem when setting up a new NRF board to run with MQTT with AWS.
When the setup is running, I get LOG <inf> for...
Hi,
we have a unit that needs to go for conformance testing.
The only external interface we have is the nNR52833s USB port (pins 12/13 on QDAA).
Alternatively can the...
Hello,
We're using a nRF52840 with S140 SoftDevice (v7.3.0) for a Central device but we're having a disturbing issue when scanning: a hardfault occurs less than 2 seconds...
Using the pc_ble_driver_py.ble_driver I'm able to subscribe to notifications, but unable to get the values upon connection. The error is:
I do not know how to install...
We have an application where we need the PWM pin state to revert to high impedance between bursts. It doesn't appear this behavior is capable by default. Is there a means...
Hi,
As mentioned in the question, I want to use the external clock as the RTC instead of the internal clock. How to configure it?
Platform: Windows 10
NCS version: 1...
For a fully connected set of node devices in a BLE mesh network, where any node device can send data packets to any other node device via an optimally short number of radio...
Hey,
upon a BLE_GAP_EVT_ADV_REPORT I call the following function:
static void pass_adv_data(ble_gap_evt_adv_report_t const *p_adv_report).
The function checks the p_adv_report...
Hello,
I'm having trouble setting up CMSIS Configuration Wizard in SES IDE v5.50a on Mac OS.
I've followed the instruction in https://www.youtube.com/watch?v=b0MxWaAjMco...
hi Team,
working Environment:
nrf52832 DK, SDK 17.1.0, keil IDE uvision 5, Windows 10 pro.
i am working with ble_peripheral based ble_app_uart example.
this program...
I am working on some teching modules covering MCUBoot and DFU ... and trying to get the
basic examples built for an nRF52840 DK board ... and am running into an error along...
