I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
Hi nordic:
NCS1.8.0 , I added UART2 to the NRF9160 LWM2M sample, but it cannot send and receive, but the same code is put into the NRF9160 UDP sample and it can work normally...
Hello Everyone,
I would like to implement a random delay of 10 to 3000ms before my development kit start advertising itself.
I'm using nRF5dk v17.1.0.
How do i go about...
Hi,
I tried to combine the spi and ble_app_uart example. But I got this problem, and the program was stuck in this loop.
Here is what I did:
I am using the 17.1...
Hello all,
we are working on new project that should work for both role (central and peripheral). If I compile the sample "central_and_peripheral_hr for NRF52833DK_NRF52833...
Hi all,
I want to implement a calendar that can be used for many years with nRF52840.
Will leap years be corrected in the nrf5-calendar-example? I looked at the code...
Does anyone have an example of using pinctrl and pwm on a Nordic device using Zephyr for a motor driver or something like that?
All the examples appear to NOT use the pinctrl...
Hi.
Setup:
I use NRF5340. Open project from SES menu "Open nRF Connect SDK project".
nRF Connect SDK Release: 1.4.99-dev1. nRF Connect Toolchain Version: 1.4.0.
Project...
Hello! I tested the ST BLE Sensor sample on my nrf52840 DK. I have a few questions about the source code: 1. Looking at recv(), connected() and disconnected() functions, seems...
All nRF5340 reference designs use via-in-pad structure. Instead e.g. nRF52840 has reference designs which can be used with through hole PCB.
nRF5340 seem to have 19 IO's...
Hi,
I'm trying to do a very simple thing - setting those pins as high or low,
but I see that it simply does not work for those pins, I see no change in led state that...
I am using the SLM app from the 1.9.1 SDK.
I connect to my MQTT broker using TLS offloaded on the modem. I subscribe to a topic using QoS = 1 Then if a message is published...
I have been trying to get mqtt to stay connected without activity for more than 30 minutes. any keepalive value over 30 minutes just results in mqtt discoonection. tried with...
On a custom board, I've got 2 inputs connected to an external pullup and a pad. One in is P12, one on P21.
When I short the pad for P12 with GND, that input read low, that...
Hi,
I tried to access Nordic devzone, yesterday and today, but got an error message that "the page cannot be displayed because of an internal server error has occurred...
Hello everyone!
I am trying to figure out how SPI drivers for Bosch bme280 sensor work... I would like to somehow recycle them to write my own SPI drivers for another device...
