Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
HI,
I wanted to know what is the default tx power set level in S130, I took a example from sdk 11.0.0, (ble Peripheral/ble_app_uart) but i dont see anywhere this example...
I struggled for a while with this: the SDK documentation and the example application did not explain a common use case: reading and writing single-byte registers in a peripheral...
I need to measure periods with high precision, so I need to make sure that the HF clock is using the external XTAL; when the softdevice is not started (for testing mode) I...
Hello,
I am building a wireless sensor network for my coffee business, I am using a raspberry pi as the gateway with nrf24l01 connected to it, I have a bunch of sensor nodes...
HI
I have followed the below-mentioned tutorial
https://devzone.nordicsemi.com/nordic/b/archives/posts/nrf-connect-sdk-tutorial---part-2-ncs-v1-4-0#h117sk6474thpzmbdphj6gan2vw7rzj...
PCB above my collection of audio data by codec, and then through the Bluetooth upload, the audio signal noise will be ticking ticking, may I ask what is the reason
hi, all
I added scan module at 'ble_app_uart' example..
Error in function nus_c_init. (0x08)
So when I follow the line by line, it seems that the 'registered_handler_set...
Hi,
Iam using Segger Embedded Studio (SES) v5.20, SDKv17.0.2, NRF52840 DK board, NRF52810 Microcontroller in the Custom Board
Since we don't have the PCA10040e folder...
Hello Everyone,
We are using nRF52840 IC for our products which has 1 MB of flash.
Thread Secure DFU Example provided with Nordic SDK supports only Dual Bank DFU. This...
Hi,
I'm working in the asset tracker v2 project and currently I need to do a simple hex to char array conversion. This entails using sscanf. However the use of sscanf consistently...
Hi, I am trying to expand on the ESB PRX example and want to recreate functions with the same functionality as Arduino's micros() and millis() functions. I'd like the following...
Hello, Nordic & all:
I have a problem when use P0.21 as the libuarte's uart RX( base on libuarte example/sdk17.0.2) for my custom nrf52840 board， I looked up the reference...
We just received a PPK2 and have used it in several configurations to test a custom nrf52832 board that runs on a 3v lithium coin cell.
When connected in the following manner...
Hello:
I am working on an application that uses a simple UDP socket for transmitting data. I would like understand the zephyr BSD socket behavior when there are cellular...
