I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
I need to control the BLE ON/OFF state and send some data to MK81 via BLE through UART, we have estalished the Hardware connection between the nRF52832 chip and MK81,
How...
So, I am quite beginer with programming and working with this sensors and nrf, So I need your guys help.
I am trying to get the x,y,z values from the accelerometer of BMX055...
The nRF 52840 RSSI "meter" is not usable.
I tested in an RF (2.4Ghz) quiet neighborhood. Using a reference receiver, I measured RSSI variance around +/-3 dB (95% confidence...
Hi
Q1. Can SES Nordic fork generate unique checksum for code verification? It's like what Microchips compiler did.
Microchips compiler can generate checksum after code...
Hi there!
Okay, we're back again... I'm using ARMGCC in combination with Make, nRF5 SDK, nRF SDK for Mesh, FreeRTOS and C++. This time I wanted to use the APP_BUTTON library...
Hi Nordic,
I am a beginner in programming outside of the Arduino IDE. I'm familiar enough with C to understand much of the code in the examples, but using I2C with the...
Hi. I am currently using an nRF52840 DK board and SDK 17.0.2.
My team is implementing a default key for the first connection to device.
During the connection, we plan...
Hello, I am currently trying to build the lwm2m_client sample on my nrf9160DK but I am facing these issues in my Kconfig file, specifically with the BSD_LIBRARY dependency...
Hi,
I noticed (as highlighted in screenshot below) some of the IP based BLE projects under “Experimental: IoT Examples” found in all previous versions of nRF5 SDK that I...
Hi
We've recently added FreeRTOS to the firmware of an existing product (primarily to pre-empt big chunks of 3rd-party code over which we have no control and execute them...
Hi,
As discussed, the instructed PCB land pattern for nRF9160 is according to Product Specification:
However, we have noticed that land pattern exceeds nRF9160 dimensions...
Hello ,
I am trying DFU over BLE.I am using SDK 14.0.2 .
i Flashed Bootloader Code and Softdevice 5.0.0 .then Device is Starting Advertised as DfuTarg and As Mention in...
Hello,
i have one nrf52840 board with a coded phy scanner and another sending advertisings, when it are close , i received in the scanner 100% of Advertisings, but when...
Hello,
I'm doing some initial investigation with the nrf9160 DK and after some reading and testing, it's clear that significant part of the low-power capabilities is determined...
