Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hello,
I work on a thingy52 since few weeks with a nrf52832 SoC. When i'm turning it on and connecting it to my computer, there is no led turn on and it is not detected...
Im currently working on BLE SMP DFU on Nordic52840DK (Connect SDK v2.7.0) based on this example:
https://github.com/hellesvik-nordic/samples_for_nrf_connect_sdk/tree/main...
Hello everyone,
I am working on a project with a Thingy91 that has an nRF52840 and an nRF9160 , and I am trying to read the battery level. I want to measure this battery...
To output PWM signal as early as possible after powering on the NRF5340DK, I added the same code in mcuboot/boot/zephy/main.c and mcuboot.overlay as in the app core. This...
In ticket Case ID 290251, Torsten Rasmussen provides the following advice to ensure that the toolchain corresponding to the SDK is used to build the SDK (this applies to nrfutil...
I am lab testing Nordic's DECT-NR+ (DECT) for a new factory automation application; I am using the hello_dect sample application from the PHY webinar demo, I am trying to...
I made a custom board, uploaded the Arduino bootloader and was flashing the firmware with Arduino I used it without any problem with revision 2 But when I use revision 3 chip...
I am developing a simple ble peripheral device that will measure temperature and humidity. For the most
part, it's working but I can't get the behavior I expect when enabling...
Hi! I'm working on the firmware part that needs to perform operations on the same variables both inside GPIO IRQ and the software timer callback. So, there is a need for a...
Hello, I want to send data from peripheral devices to central device. My peripheral device code is based on "ble_peripheral_uart" sample and my central device code is based...
Hi, I'm working on developing a UWP app that can detect any or compatible Nordic devices. let's say a device has BLE capabilities, then through the desktop app i should be...
I have both a nRF5430DK and a nRF9151DK (or 9161). If I wanted to develop a solution with both BLE and LTE, how do I set up a DK environment for them to work together? Do...
Hello , I 'm trying to use the Lan865x (two -wire eth click ) chip with the nrf52840dk board , using zephyr 3 . 7 . I 'm getting always this error while trying a net sample...
I'm working on custom test software for use in production programming/testing of my product containing a nRF9160. I'm using the nrfjprog executable, but with problems, every...
Attempting to attach NRF9160-DK to Verizon with a Verizon data SIM only obtains IP address.
Internet access is limited to DNS within Verizon.
Submitting the IMEI to: ...
