Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
I am inquiring about the ability of the nRF9160, does the device have the resource to be a picocell? Specifically, can it handle communication to and from a single cell phone...
Hi
I‘m working with the SDK since many versions. One thing I don‘t understand is the sdk_config.h concept.
My first thought was that there is a master sdk_config.h in...
Hi, I made a PCB board nrf51822.
Because of my mistake, Rx, Tx pin was not cross connected to MCU.
So i want to change Rx <-> Tx pin.
In the example of ble_app_uart_s130_pca10028...
hi,everyone
when i test the mesh/example/dfu , it is upgrade scucessed,but when i combine it to switch_light example ,it was failed , it looks end the transfer too early...
Hi, there~
I'm trying to make my own bootloader and starting with the secure bootloader sample code.
The problem is the orignal bootloader, that is compiled with secure...
Hello,
Recently I started working on BLE. I need details with respect to BLE 5.0.
Below are the features of BLE 5.0
2x Range (With 2Mbps PHY)
4x Speed (With...
Hi,
I've created 3 PWM pulses via:
Which works when I'm not starting Thread (from the examples/thread/freertos_coap_server example)
But when I start Thread...
Dear Sir,
I am working on the following scenario.
I have BLE device ( SDK 15 and softdevice s132). It is advertising for specific duration.
There are different phones...
Hi,
I am working on a project where I am sending and receiving Encrypted string data from my phone with nRF Toolbox to the nRF52840 DK. The basic paring is established along...
I recently got past an issue with not connecting to the LTE network getting an nrf_cloud_connect failed: 60 and had things working yesterday. I had support for that issue...
Hey, I'm trying to connect a touchscreen monitor (10 finger) usb into a computer, get a raw input report and send it over uart to bluetooth module and sent it to other computer...
In IAR it shows the cycle count registers and they appear to work as expected in that view (shown as CYCLECOUNTER) . In the IAR Project/SFRSetup it shows the address of DWT_CYCCNT...
Hello,
I am developing a simple HID device with output report to receive data from PC. I took keyboard example as base project and I want to increase output report size...
Hello!
I have a custom nRF52832 board with an FTDI usb/serial part running my app successfully.
I generally program the board with a JLINK and SWD, but I am working to...
Hi, I apologize for the question renewal, that is the same as ticket "SDK15 DFU and WatchDog issue" (for my mistake I closed the discussion post!). I have developed a custom...
