Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello, I am looking for a way to debug firmware that includes MCUBOOT. There seem to be quite some questions in regards to same problem with no real resolution. I am using...
Hi,
I am new to the NRF boards and I want to include the cJSON library into my project code. I am going to get some data from another device using in the cJSON format and...
Hi,
I have used nRF Connect for very long time, and have just upgraded to v5.0.1. The software seems to use a sandbox tech and restores nrfutil.exe to its default version...
Hi
I want to update the ble advertising data in my program. In nrf5340 the bt_le_adv_start() command should run only once in the main program.
Is it possible to change...
Hello,
In our project we are using FLASH 2GBIT SPI/QUAD W25N02KVZEIR external flash together with nrf5340. I have made the flash definitions on v2.6.0\zephyr\boards\arm...
Hello,
I am trying to bring up a MBN52832 Bluetooth Low Energy Module supplied by Murata that uses the nRF52832 chip. The BT module is connected to the MCU(STM32F427) via...
Hi,
We are working on nrf5340 board with NS and TF-M setup and we have SDK v2.7.0
We need to have a flash partition to store the some secure data may be a size of 4KB...
The sidebar does not load, this is version v2024.7.13.
I uninstalled it and installed it again as an admin, but it still did not load.
Sometimes it loads for a split second...
I am using a custom board with a nRF52832 (inside a BMD-300 from ublox) that I can't seem to get to a lower power state. The lowest I've been able to get is 2.2mA even using...
Hi,
I'm developing an application on the nRF9160DK with custom firmware for both the nRF52840 as well as the nRF9160 on the board, using VSCode with the nRF Connect extension...
Hi,
I am working on an application with ncs 2.5.0 that is based on a combination of the central_uart example and the hci_lpuart as I'm trying to pass data around between...
Hello,
My goal is to read out UICR address 0x10001080UL from command line / MCUMGR.
How to acheive that?
I have tried and successfully compiled ran these mcumgr handler...
I am useing NCS v2.6.0. Setting "CONFIG_LOG_MODE_OVERFLOW=y", will always print "1 messages droppend" after a period of RTT printing. CONFIG_LOG_MODE_OVERFLOW =n will no longer...
