Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
HI Nordic Team,
I am developing a firmware to interface CH101 sensor, which has a firmware loading of 2048 bytes of data over I2C.
I declared buffer size as below in device...
Hi,
As i understand from the docs, the max throughput for BLE in nrf5340 is 1.4mbps. Ideally, we would like to achieve this, however anything near to 1mbps would be great...
hello,
I would like to know which operations were performed on all chips by the `nrfjprog --recover` command.
"The nrf52833-B chip is by default enabled for read protection...
Hello everyone,
I’m new to the Nordic development ecosystem and currently working on a project to implement a temperature and humidity monitoring system using the nRF9160...
I'm currently working on a project using the nRF52840 board with the MAX30001 ECG sensor. I'm using nRF Connect SDK with VS Code version 2.6.1 to develop the project on Zephyr...
I am using nRF9160 to develop a mobile measuring device.
For this purpose I need LTE and GPS, I know it is shared so I had to implement PSM/eDRX to make it work together...
Hi
I am working with a sample project (Bluetooth: Peripheral UART) for nRF5340DK in VSCode.
So I have installed the nRF Connect extension.
When I view the currently...
\nRF5_SDK_17.1.0_ddde560\examples\peripheral\pwm_driver\pca10040 In Demo1,i assigned the same pin to the 4 channels. I expect every cycle LED0 has the same behavior. But,...
Hi Networks,
I have tried to build the nRF5340 DK as a gateway.
Enabled
1. CONFIG_BT_GATEWAY=y
2. CONFIG_BT_GATEWAY_ADV=y
3. CONFIG_BT_GATEWAY_GATT=y
But not acting...
Hello,
I will be designing a board using with nRF52833 with the NRF21540 for the added gain. Would it be possible to add adaptive frequency hopping?
Thank you,
Shah...
The central device has the below settings
One central device A and two peripheral devices B and C, B and C have the exact same firmware. A can establish the connection...
Hello
I have implemented the stereo function to the nrf5340 audio application on SDK V2.6.0. i can send stereo audio signal to both of the two headset at the same time or...
Hi, I recently got nRF5340 Audio DK for my work. I have been try to use the onboard mic for collecting audio and transmit it via BLE, since I'm a newbie I couldn't do it....
Hi
I have successfully added the nrf_crypto files to the UART project. It compiles without any issue. Now I was trying to run the ECDSA example code in the UART project...
I used nrf52840 board with SDK 17_1_0
I used segger embedded studio IDE
i want to Implement two VL53L5CX TOF sensor with nrf52840 so i used two TWI,
but when i init...
