Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
I have tested NPM1300-EK with NRF52840DK and it works.
However, I am using other MCU with NPM1300 but it is a non -zephyr project.
To work with NPM1300, I have tried...
Hi,
I am using nRF7002 DK. I have set P1.04 as UART RX. For testing I am using TI CC26x2R1 Launchpad to send UART data to nRF7002 DK. I use a logic level shifter board to...
Hello,
I am currently trying to connect an external hardware codec and amp (Adafruit MAX98357 I2S Class-D Mono Amp) in order to play audio via BLE Audio and I2S using...
I have an NRF9161DK 1.0.0 , I was trying to do some wiring but the sensors didn't work, then I noticed that the board delivered 1.7v.
I tried changing it to 3.3v using the...
Hi,
My NRF52840DK ( pca10056 1.1.0 2019.9) would not reset when I press its Reset button. The issue is very similar to https://devzone.nordicsemi.com/f/nordic-q-a/38555...
I have new Thingy 53. Default Edge Inpulse demo works without any problem. But I have problem with Weather Station demo.
First I tested Zigbee version. After flashing using...
Hi,
What is the minimum LDO dropout voltage of nPM1300? For instance, in order to get 3.3V from the LDO, what is the minimum input for the LDO ? On the datasheet there is...
Dear all:
I have prepare env for border router successfully following this link( developer.nordicsemi.com/.../tools.html , Raspberry Pi4 and nRF52840( RCP: radio coprocessor...
I have a customer that wants to provide me with .a file for some confidential algorithm they want to run. I am tasked with implementing this into my firmware.
Using the...
I can't seem to get the FIFO to work and I think it is because I'm not dereferencing the consumer thread properly. I have reviewed the nRF Connect SDK Intermediate, data passing...
Hi,all
I need to connect BLE via NFC,but I do not know which example should i use to start。and i am a new field of NFC ,is there some document about NFC?thank you a lot...
https://devzone.nordicsemi.com/f/nordic-q-a/44658/communication-probl
I want to change the code provided in this link to enter the password from the peripheral
Hello,
I am using nRF Connect 2.5.2 with a Xiao Seeed BLE Sense nRF52840 and Jlink EDU mini
I am trying to flash the peripheral_hids_keyboard sample with Ozone, and I...
