hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Dear Nordic,
Could you please help me to understand the concept of using the DTS files and board initialization sequence?
We have just one GPIO port to control some external...
I suspect the EXT_SWCLK/DIO and SH_SWCLK/DIO pins on the SEGGER chips of the PCA10028 were burned. Is there anyway I can fix it? I have three of them behaving the same way...
Hi,
We are ready to launch product that uses nRF52840 + s140 v7.2.0.
We need its QDID for EPL.
In Bluetooth SIG, we found the following page, where we could find DID...
Hello!
Recently I was asked to find a way to enable timestamps in our debug logs to make it easier to track performance during various stages of the operation of our device...
Hi everybody,
I am running into the same issue as described in this post:
https://devzone.nordicsemi.com/f/nordic-q-a/50386/ble-scan-timeout-always-in-multiple-of-second...
I've been working with the NRF52840 for a while now. My setup is based on the CLI coordinator code and a bunch of end devices running the multisensor freertos based program...
I am trying to use a remaining timer/counter in the nrf52832 as a divide by 64 counter to get rid of an off board MC74HC4060 counter chip we are using for I2S from an external...
Hi Nordic Semiconductor!
Over the years I've been using your development kits, some days ago I got the nRF5340-DK and started on a new computer. Normally I dive into the...
I don't know why, but after issuing the nrfutil dfu command line, it takes ~34 seconds before the DFU starts and the progress bar is shown.
Sample command lines:
nrfutil...
Hello,
I want to use a FIFO. I want to send the data from file1.c and receive it on file2.c.
Currently, I have defiend my_fifo using K_FIFO_DEFINE(my_fifo) and using...
I am currently working on AoA direction finding solutons, and I have successfully run the demo direction_finding_connectionless_rx and direction_finding_connectionless_tx...
Hello,
I would like to ask you if there is an antenna layout available for the nRF52833. Indeed, I would like to develop my own application with it and, this SoC needs to...
Hello all,
I am currently working on receiving SAADC data and transmitting it through BLE with a sampling frequency of 1kHZ or higher. I am using nRF52832 board with the...
