Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hello.
I want to use the nrf52840 as Bluetooth radio controller which is connected over UART to Linux based ARM host.
We are targetting to use meshctl on linux host...
Hi ,
We are facing a problem with cellular connection in NB-IOT mode on NRF9160. We are trying with the asset tracker sample , but cellular connection does not happen. Can...
Hello Everyone,
I started to use the NRF52832 recently and wanted to use it with a sensor from Melexis called MLX90632. I am using sdk 15.0.0.
This sensor have a library...
Hello,
Currently I would like to add a functionality to Bluetooth Low Energy App (BLE). I have a bluetooth slave device that require a specific sequence of sending string...
So, i have been trying to perform a DFU over serial using the method mentioned here by Hung Bui.
Here is a summary of what i did:
- build and flash mcuboot
- build and...
I am using pc-nrfutil to perform FW upgrade (transport is serial), The target is custom board with 52840 processor, running Bootloader adapted from the SDK.
For most of...
I've configured the SPI with DMA module as in the code below.
I've loaded the tx buffer with sample data and start the transaction; however, I'm not reading anything either...
Hello,
I have been working on porting the BLE UART PHY S erialization to the STM32L476 (with a Nordic NRF52832 Dev Board and STM32L476 Nucleo-64). I have read the porting...
Dear Nordic,
Running BLE mesh sensor network with multiple servers and a single client linked to a gateway.
SDK: 16.0.0_98a08e2
SDK Mesh: v4.0.0
nRF52840
The client...
I'm attempting to using pa_lna_setup(), specifically the softdevice function sd_ble_opt_set to enable/disable the radio and an external amplifier. My application is a custom...
Hi All,
Im trying to flash the pre boot-loader from here github.com/.../releases
to my nordic usb dongle.
hex-> mdk_nrf52840_dongle_bootloader-0.3.2_s140_6.1.1.hex Im...
Hi Team,
We are using the uECC library for ECC Functionalities, while connecting the debugger we are getting the pop up message like "not finding the source file".But while...
Hello guys,
I have nRF9160DK board here with me and the nRF Connect SDK v1.3.0 environment installed. I want to connect to AWS IoT Thing through the MQTT connection.
I...
When I was testing USB on SDK16.0 with nrf52840, the gateway acted as the host, the following scenario 1 worked abnormally, and scenario 2 worked normally.
Scenario 1: When...
I am using NRF5 on an NRF52840 board, building under GCC. My application needs FreeRTOS and I also need to be able to use stdlib functions such as printf() from any RTOS task...
