Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
Hello everybody,
I can flash my custom nRF52832-based PCB using the nRF52 DK and Segger Embedded Studio or nrfjprog, but this requires that I always have my computer with...
Hi,
I need to get 1.8V on the VDD using high power mode. According to the documentation this is the default value. However, I measure 3V.
Please advise,
Daniel
I am developing a nRF-Mesh based product. This product consists of a fixed number of nodes in a Bluetooth Mesh Network. Are there possibilities to factory-provision a set...
Hi!
I am working with experimental_ble_app_eddystone in SDK 12.2.0 for nRF52.
I have seen that the firmware does not support using different advertising inteval for each...
I'm wondering whether or not nRF52840 can be used for a USB smart card development.
"According to the spec of a USB CCID device (which could be found on www.usb.org ), there...
Hello everyone,
After using IPSP intiator and IPSP Acceptor BLE Examples on 2 different kits and connecting them through this profile, how do i send IPv6 packets between...
I cannot get a connection between Seeger Studio and a dev board from Seed Studio called nRF52832-MDK
I have added a pull-down resistor on TDO as I was getting an error that...
is advertising Complete List of 128-bit Class UUIDs(0x07) a doable ? I mean like " Complete List of 16-bit Class UUIDs " (0x03) it's not a service, just has an information...
Hi,
I'm debugging a Nordic mesh example, which is named light_switch_server_nrf52832_xxAA_s132_6.0.0_Debug, after build and go, a message appear:
sd_ble_enable: app_ram_base...
Hi All,
Hoping this is straightforward for an intermediate developer.
nRF52840-DK (matched dongle not yet in use), SDK 15.2.0, SES 4.10a (Jlink 6.40), Windows 10.
My...
Hello,
I have seen that the nRF52840 PS v1.0 specifies the RSSI_PERIOD to be 15us. I have also seen that the nRF52832 has only a RSSI_PERIOD of 0.25us (PS v1.3+) or 8us...
I need some technical information:
- the micro Host can (through a pin?) make WakeUp of the BLE module to configure it / change the operating parameters etc? - the BLE module...
While visiting the Nordic Tech Tour we were discussing the pros and cons of BLE Mesh with a Nordic employee. He recommended that we also looked at a different solution, a...
This is essentially a repeat of :
https://devzone.nordicsemi.com/f/nordic-q-a/38808/is-a-3-bit-synchronous-3-data-lines-clock-parallel-input-at-16-368-mhz-feasible
Instead...
