Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi.
I want to change device name to identify multiple devices.
When I am using two device, the initial device name is "device".
If I connect these two device to iphone...
I have an application that needs to minimize its current consumption when sleeping. From the nRF52 manual, I see that UART should consume 1uA when in idle. The total current...
Hello,
I'm using thhe BLE shied, which uses the nRF8001 chip, with arduino Mega.
I'm trying to connect the Rf module nRF24l01 to receive data from another arduino and...
When checking if a read (or write) is authorized can the event contain an invalid handle (Does the handle need to be checked)?
case BLE_GATTS_AUTHORIZE_TYPE_READ:
{
...
hi
in nrf51422
till now this is my code
now how can i send or recieve information .
or tell me for sending information what to read next?
#include <stdint.h>
#include...
Hi ,
I want to call a pstorage_store() function to update the flash content when ble receives the disconnect event.
My doubt is whether i be missing the flash write event...
I am working on a system with dual Bluetooth chips one acts as primary and the other as secondary.
I want these two communicate with a shared resource(Accelrometer)...
currently, i connected the nrf52(spi master) with ads1292 (spi slave) which is a ECG sensor. For the ads1292 chips, there is a output pin generating the signal called DRDY...
Hello evryone,
i cloned button example form github to sdk version 9.0.0 and i modified the neccesary changes between app.gpiote.c//nrf_drv_gpiote.c files and set the GPIOTE...
HI,ALL
there are two 'uart_event_handler' function in the project.
one in main, and the another in the app_uart_fifo.c
with the source code, i think when i input...
Hi everybody
I make an application which combine ANCS and NUS services on my device (nrf51 SDK 9.0.0,softdevice 8.0) This application works properly when I use IOS device...
Could you explain why 8 reload registers exists. Its use and use case. Since I believe we need to reload every register each time we have to reset counter.
I have a rare issue where my device won't advertising as it is waiting for a Pending Flash event to clear. However I want to add a supervisor time-out to this. It is safe...
Hi ,
I am getting error in pstorage_store function .
On further digging function
if ((!is_word_aligned(p_src))) is returning the error.
What does this function check...
I use nrf51822qfaa,s110 v8.00,keil MDK IDE. If the program is wrong,The chip will reset, I want to save some data to the FLASH area before the chip reset. What I need to do...