I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello everyone, I took the example code "ble_app_hrs" and added a pin toggle to verify that the code is loaded correctly onto my custom board, which is programmed via the...
I'm trying to install the toolchain manager on a new work computer and I'm running into issues that I think are related to my work's proxy.
I've tried following the steps...
I am trying to configure the STS4x temperature sensor by Sensirion on I2C on a nRF5340DK, I have setup my the coding exactly how sensirion suggested except few changes such...
Hi,
When I try nrfsdk/zephyr/sample/bluetooth/periodic_adv_conn. I notice that the max subevent data size is about 64bytes. If I send a data size larger, I will get a error...
Hi DevZone,
I have made a custom PCB with the nRF52832. I placed the same coaxial connector that is on the nRF52 DK in my PCB. At this point, I want to test the BLE functionalities...
Hi,
I am unable to build the MQTT over Wi-Fi lesson 4, exercise 1 using the nrf7002dk_nrf5340_cpuapp board configuration, but the same code builds successfully with nrf7002dk_nrf5340_cpuapp_ns...
Greetings all, Does the Direct Test Mode (DTM) app v2.4.1 provided in the NRF Connect for Desktop v5.0.2 package support gain settings for the nRF21540 FEM such as +10, or...
I am working on nrf52840 and I want to control the motor speed so I want to generate the variable frequency PWM for the same. How can I generate the variable frequency PWM...
Hello,
I need to configure second UART for nRF52840 DK. So I would like to know the overlay file for uart2 configuration with exact GPIO pins. Also the .c file to initialize...
I 'm porting code from Zepyr 3 .5 to 3 .7 and am having errors in my ds2484 1 -wire device . It was working fine but now reports an init error unless I add deferred -init...
L.S.,
I'm trying to build an "Arduino" port for the nrf52840 (Seeed board).
When building an example I'm getting the following errors during the link phase:
.\Objects...
Hello,
In my project I have b0, mcuboot and an app. My nRF SDK version is v2.7.0.
My project works fine if I use an absolute address in SB_CONFIG_BOOT_SIGNATURE_KEY_FILE...
Hi,
I am working with the nrf9160 and ncs2.7. Is it possible to programmatically change how pins are defined? For example, on startup 2 pins are for I2C (SCL and SDA) and...
