I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Good day
I have been testing sample code code, but when compiling I get this error
nRF5_SDK_17.1.0_ddde560\components\libraries\uart\retarget.c:101:23: error: unknown...
I am plugging the nrf52840 Dongle to the USB port, the computer beeps as it recognizes a new USB device, but when I open the Programmer app from the NRF desktop connector...
Hi,
I am a very beginner in Python and BLE. I would like to use a nRF52840 Dongle to connect to a Bluetooth Device, send 6-Bytes data in the 1401 section and also perform...
Hi All,
i have been working on two i2c devices
1. MPR121, which has slave address (0x5A)
2. PCF8583, its address is (0xA0).
I am using Zephyr I2c api for the same...
Hi,
I would like to ask on where can I find or set the advertising duration or on how long the advertisement would last?
I am using zephyr, nrf52840DK. I want to be able...
Hello,
So, as per the requirement for my project I need to program the Thing:53 using Visual Studio code programmer following the instruction as provided in the below link...
Hi,
Is it possible to perform a HW reset of modem core inside nrf9160 device? If yes, how is this HW reset requested?
Thank you very much...
Regards,
Emerson ...
proj.conf:
nrf52840dk_nrf52840.overlay:
code:
Pretty straightforward. I've looked through the nRF52840 Product Specification and there is no mention of data bits...
From zephyr/samples/sensor/lsm6dso, I found the following code using sensor_channel_get(). API from sensor.h.
}
However, there are more driver API in zephyr/drivers...
Hello I don't see any change in RSSI with different TX power values under Zephyr. 1.9.1
It used to work with Nordic SDK 3.2.0 (see table below) The HCI API in Zephyr that...
On nRF5340, we are using Thread communication, Wifi and LTE-M module.
User can change the interface board, between Wifi or LTE-M module on the same UART bus.
& uart0...
I changed the central UART example to work with a demo I'm writing. I removed the hardware UART part and only send messages to a peripheral. What I do is I measure different...
I'm using an nRF52840 and SDKv17.1.
I have an active-high interrupt source connected to a GPIO pin. I understand that a GPIO should be able to wake up a system from system...
I think the nRF Connect toolchain is missing the right driver for the CLI app on the USB dongle, or the CLI is not setting up the USB interface with the right VIN.
When...
Hi,
Trying to run one of the Acconneer samples I get the errors below:
service_handle = acc_service_create(envelope_configuration); returns a NULL handle, all up to this...
