hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
We are developing a blood glucose meter based on the nRF51.
To comply with Bluetooth Continua, do we just implement the Glucose Profile and Service (GLP and GLS)?
Do you...
Hi everyone,
I pass few days to try to fix my issue whiteout success.
I'm working on UART example provide by SDK 10 and tried to set up a communication from my computer...
Because of the power-saving support, I want to disable the UART before Call the sd_app_evt_wait().
I referred to two following sites to know the procedure of the case....
I'm working with a nrf51422/s110 dev kit on which I downloaded the Heart rate Monitoring sample project. On my PC, using a s130 dongle, I connect the device and wrote some...
Hello,
I would like to know about the possibility of programming the nrf51822 with a Keil ULINK-ME Debug Adapter (or, if necessary, Keil ULINKpro) instead of the recommended...
Our product has a legacy interface and for security reasons I want to allow users to disable or enable the BLE via this legacy interface.
My approach to this was to disable...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hello,
I am having much fun with nrf52. I'd like to implement SPI read (few bytes) per GPIOTE event over PPI, the source is the GPIO event and the destination task is a...
Hi,
I'm working with the nRF51822
I'm trying to enable the use of some timer callback on the ble_app_template.
I've succefully created and started all the timers, but i...
I have a modem connected to some pins on an nRF51822 on a custom board. Two pins on the modem are active low. One is a reset pin, the other a VCC control. I want these pins...
Can the nRF51822 DEC2 pin (LDO output) be used as a 1.8V supply for low current use (say, <50uA)? Similarly, how about the 1.9V output of the buck converter (AVdd)? The current...
I'm wondering if the latest version (8.x) of S110 supports BLE 4.1's "Connection Parameter Request Procedure". This procedure is described in the BLE 4.2 spec Volume 6, Part...
I previously used Jlink to upload code to my nrf51. However, the new units I got are "locked" and I need to use nrfgoStudio to unlock and fully erase the chip.
Is there a...
Hi, I wrote a sample application to remotely control and led on nrf51822_xxaa module. in the application I was able to provide configuration to the characteristics as well...
