I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hi,
Is there any method that I can use to get the LE Packet or the Baseband packet ( With Access Address) passed onto the application? (Using S110 or S130)
Thanks
I started by compiling BLT uart app successfully on MDK5 but found out that it is giving errors on the startup files in the Device Pack.
I tried to refresh and update Device...
Hello Everyone,
I am trying to measure the (3v)battery voltage by having proximity example as reference but intially it is showing 100percent later it is going to 13(percent...
Hi,
SDK: v11.0.0.2-alpha
DK: PCA10040 (NRF52)
I am trying to build a peripheral application that communicates with an external device via UART (h/w flow disabled)....
Hello!
I have PCA10006 with revision QFAA nRF51422
I am testing the buck converter's ability to make the system consume less power when transmitting.
Example is ant...
hello there! i am working on project in which my one nordic BLE(A) want to send command to second nordic BLE(C) which is not in my range. now there is third nordic BLE(B)...
Hello Guys,
I would like to know, can i use NRF52 Preview DK on Board Segger Section as standalone Segger JLink Programmer for NRF51?
So, is there any way to dis connect...
Hi, I read about concurent operation of the Softdevice and other proprietary stacks like esb or gazelle using timeslot api. Is it possible to run two ble stacks in this way...
Hi Guys,
I would like to develope a HID device on nRF52832 chip. I'm woring with nRF52 Development Kit (PCA10040, v0.9.0).
I've tried to flash the board with both hid...
I'm getting the NRF_ERROR_NO_MEM when I try to put my ADC interrupt routine into the scheduler. The code runs without error if I run from the ADC interrupt handler directly...
Hello ,
I am testing the DFU support and usage for the next phase of my project. I am using S110 softdevice 8.0 and SDK 9.0 and evaluation kit nRF51822QFAAG0.
I followed...
hello, I have some quesetion about the nrf51822's carrier detect. I want to use " CSMA" to avoid
Communication collision, the datasheet has no detailed infomation about...
when I call pstorage_store so store a block of data, sometimes I call just after pstorage_store : the following code
do {
pstorage_access_status_get(&count);
} while...
In this post , I can register a new case with some required parameters to have the current estimation, but I don' t know how to obtain some of them.
I'm using nRF51422...
on the log of nRF Master Control (mobile version) I can see DEBUG VERBOSE APP WARNING . I want to know if there is a directive on SDK 10 (functions) to send those kind of...
