Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I migrate an app from NCS 3.1.0 to NCS 3.2.3.
Using mcuboot with a Thingy:91 or Thingy:91X fails.
flash_img_init results in a flash_img_context, which uses ID 2, the application_slot0...
Hi, Nordic Support!
nrfutil is a replacement for nrfjprog. I have previously relied on pynrfjprog for automated testing and programming. This test procedure uses RTT shell...
I've noticed weird behavior in the software timer scheduling. I my case, there is one timer handling LED blinking. It is used in single shot mode and rescheduled to time the...
I will like to know whether the NB-IoT feature User Plane CIoT optimisation is supported in nRF9151? And if the feature is supported I will like to know the AT command to...
Hi,
We are considering using the new sEMMC SoftPeripheral on the nRF54LM20A with a 4-bit SD card or soldered SD NAND instead of eMMC.
Has anyone tried this? Does it work...
Hi,
I'm in the process of porting our existing nrf5 project to nrfConnect SDK bare metal and am struggling to port our QSPI display driver. Are there any plans to add support...
I’m designing a PCB using NRF9151-LACA-R7 and an NRF52810-QFAA-QFN48 Our CM needs the exact temperature data for SMT reflow , but we can’t find it clearly in the datasheets...
I just developed a BLE peripheral using an nRF54L05 MCU powered by an nPM2100 PMIC. When I flashed it with a simple blink LED firmware using a JLink via SWD, everything worked...
We develop Class C software for a medical device on the nRF54L15 with the S145 SoftDevice. We are also evaluating the nRF54LM20A. We use only the nRF Connect SDK Bare Metal...
NCS 3.4.0 - Thingy91X
If I configure the sysbuild with sysbuild.conf
SB_CONFIG_BOOTLOADER_MCUBOOT=y SB_CONFIG_SECURE_BOOT_APPCORE=n
it builds, but on "west flash" I...
Hi,
1.What is the maximum rate that the QSPI of nRF54L15 can achieve? 2. Is it possible for me to use QSPI to read the flash memory while simultaneously refreshing the screen...
Hi,
I want to ask if the Nrf54l05 supports application image compression. I asked Nordic AI and they said it’s not supported, but I want to know the reason why it’s not...
I'm setting up a board I just built in NCS, and I made an overlay file for it. Specifically, I am setting up the UART21 peripheral and assigning pin outputs. I made a mistake...
I have a school assignment revolving a technological product, where i need to ask a few questions to a business about their involvement with the product. Therefore i need...
