Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
I'm developing a device that occasionally bursts large data payloads (~30kB) over BLE. It uses MPSL to share the radio between BLE and ANT+, so I'd like the BLE radio to use...
In the documentation , it is stated:
The SAADC is preceded by a gain stage which has a programmable gain. The voltage range seen at the input of the gain stage is:
...
Hi:
I'm doing the exercise L3-E1.
I used nRF Connect SDK Toolchain v2.7.0 because it didn't work with v2.8.0
How do I make NRF Terminal appear?
Thanks and Best...
Hi
nRF54L15-DK QFAAC0, ncs v3.4.0, project path: ncs\v3.4.0\zephyr\samples\boards\nordic\system_off
After compiling and flashing this example, the power-on reset (POR...
Hi Nordic,
I am uing DECT NR + on NRF9151 and trying to do some kind of network discovery like knowing how many devices available in the area. As far as I can do with the...
Hi,
In the NRF54LM20A Development Kit, in addition to the tank circuit (L5 + C8) in the path between DECA and DECRF, there is also a filter made from C7=2.2uF and FB2...
Hello Nordic Team,
I am working with an nRF52840 on a custom hardware board and investigating the current consumption in idle condition.
I have tested the same hardware...
I’m using NRF Connect SDK 3.2.4 with the nRF54L15-DK. I’ve successfully used the nrfx_gppi_conn_alloc() and nrfx_gppi_conn_enable() APIs to connect a timer to a GPIOTE output...
Hi,
I have a custom PCB with an nRF54L15 with custom PCB trace NFC antenna working currently with ncs v2.9.1. The NFC is used for commissioning and reading out parameters...
Hello everyone! We were working with our nRF52DK boards and one of our students had issues flashing a board. He used a recent version of Segger J-Link Commander (V9.30 as...
HW: nRF54L15DK
Phone: Pixel 10Pro Android 17
When trying to use nRF tools to test channel sounding i am only able to get the infreqent mode to work, both normal and frequent...
Hi,
From this old thread, nRF Sniffer seems can decrypt the mesh packet.
But I still failed with add network key, application key, device key and IV index.
I attach...
Hello, I am developing in a Zephry environment on the NRF5340 and am looking to enable APPROTECT and ERASEPROTECT on our NRF5340 MCUs. We want to enable a recovery key so...
