I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hi,
I have a mesh network with multiple smartphones, which are connected over GATT. If now a light command is triggered on one smartphone, I want to synchronize the other...
Hi Sir,
As we know the SDK has the lowest version of IDE to compile.
========= release note of SDK 16.0 ============
The following toolchains/devices have been used...
Hi,
Every now and then we have to fix bugs in nRF Connect SDK. Some of the bug fixes are of general interest. What is the process for contributing fixes to Github?
BR...
Debugging in Segger serial example from mesh
It runs and responds to commands, but when paused or hits breakpoint - single step or continue gets to address 0xa60, continue...
While setting u p a sample project in SEGGER Embedded Studio, following error is encountered
All the previous installation steps were successful and verified.
Please...
Hi,
I am trying to implement SPI slave on NRF52810. I added nrfx_spis.c and enabled below macros in sdk_config.h
NRFX_SPIS_ENABLED and NRFX_SPIS0_ENABLED to 1
Still...
Hi all,
I am using SDK 15.3 with NRF52811 chip.
My application include app + bootloader.
In my application, I use flash area from 2E000 to 2F000 for save my user data...
hello
i want to create for the need of my project a thread border router as simple and compact as possible.
i have seen the implementation using a raspberry pi 3B as the...
Hi,
I followed this guide to send data to the GCP using the Thingy:91 : https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/how-to-connect-nrf91-to-google-cloud...
Hello,
i'm trying to set the automated test script as described here:
https://github.com/NordicSemiconductor/Android-nRF-Connect/blob/master/documentation/Automated%20tests...
Hi all,
I am a newbie in ble and also nordic. I have an application need that would do some lowfi sound data transfer which 16 bits at 14k sample rate from central device...
Hi,
Good Day!
Statement of problem: Currently we are using app_timer in our application for conducting the user behavior. For example, for user input off of capacitive...
Hello, everyone. I am newbie in use the Power Profiler Kit I followed all the steps as described in PPK User Guide v2.2:
1 - cut traces on the DK (SB40) 2 - installed the...
Hi,
I am porting a BLE program in nRF52832 EVB, and it can work correct.
The system will not work when I want to remove 32KHz crystal from my own real board.
Would you...
Hi,
So we are currently debugging our custom nrf52832 board. It is equipped with both a 32.768khz and 32Mhz Oscillator, which both SEEM to work.
I tested both using the...
