Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hi, I try to launch west build command from a terminal.
I am first generating environnement variable as stated in this post :
Then I call it, and finally, I launch this...
Hello,
I am working on a custom board designed around the NRF52840. Currently the bootloader on the board is the same as the one on the NRF52840 DONGLE. It is out intentions...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
My goal is to achieve a data throughput...
We are connecting nrf boards to solar charged batteries for power consumption. We will be remotely deploying the boards on field. The boards are connected to sensors, from...
I'm going from v2.6.1 to v2.7.0; I'm using a thingy53. I'm getting a voltage error prior to boot.
[00:00:00.002,929] <err> voltage: setup: -134 *** Booting nRF Connect SDK...
Hello.
Wiring 1:
wiring 2:
Background to the case: We tested this with 2 different ppk2s and always got the same results. Our custom board works fine if we wire...
Hello,
I'm using nRF9160 as a HCI host and nRF52840 as HCI controller (nRF52840 config is based on HCI lpuart example). My application receives data over Bluetooth using...
Hi,
I evaluate MCUBOOT and trying to understand how it works. I am using a nRF52840DK. I have base my demo on this course ( Exercise 1 - DFU over UART - Nordic Developer...
Hi,
We would like to disable all wakeup sources before calling sys_poweroff. How to achieve this using Zephyr API? Pin configuration should remain as previously configured...
Hello,
I'm trying to enable the Power management for nRF9161 over nRF-Connect SDK2.5
the prj.conf has an entry of 'CONFIG_PM=y'
but it not accepted because we do not...
I am running the demo about knx iot. (branch: v0.3.0_rc in https://github.com/NordicPlayground/nrf-knx-iot )
I build and run "light_switch_sensor" and "light_switch_actuator...
basically, I want to use dm feature in connection-oriented communication. not in connection less, and I want to connect 1 central to 4 peripheral and measure distance.
Can...
nRF Conncet for Desktop v5.0.0
Hello,
I have some trouble to update the Toolchain Manager of version later than v1.2.6. The download fails. However, I can download the...
Hi,
We are working on a project using the nRF52832, which utilizes UART for a QR-code sensor, I2C for an OLED display, and SPI for external flash memory.
We are at the...