hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
I have software on my PC with an NFC reader attached, that connects to my nRF52 devices, reads the NDEF tag, modifies it, writes it back, then reads back the modified value...
Hi,
I've been trying to get the button events from the nrf52832 where FreeRTOS is enabled.
https://gist.github.com/gpgabriel/f070e39f335da8579e9a577b44109237
The 2 function...
Hi, We are testing the dfu ota example for the PCA10040. In our application we have some default values and settings are stored in the RAM. nrfutil is unable to generate the...
Hello,
I am using the Thingy app for ios as reference to read my own temperature sensor. However, I am reaching a point where I get stuck.
I cannot understand/find where...
Are there any limitations when the central is connected to 20 peripherals at the same time? Is there a minimum connection interval (ie, can I set them all to 7.5ms?).
Hy everybody,
I'm trying to implement DFU bootloader in our custom board, starting from the "bootloader_secure_example", where I just changed leds and button pins in order...
hi,
i am doing nrf_mesh_dfu example with nrf_sdk_for_mesh v1.0.1.
so far i am able to generate device public_key and private key by following instructions .
and also...
Hi, I get a hard fault when I try to add an own UUID to the softdevice S132. I'm using Eclipse with GCC compiler, Rigado BMD350 eval board with the nRF52832 chip on it. As...
Hi Nordic DevZone ,
I wanted to enable the new feature Advertising Extensions in the example application light_switch and see how it works, but unfortunately i can not...
Hi,
i am evaluating the use of the nRF51822-QFxx for our product and made good experience with the nRF51-DK. Now, i would like to layout the custom pcb and i am not sure...
Hi
The definition for nfc_t4t_ndef_rwpayload_set() is that it takes buffer_length parameter.
And the comments state "buffer_length Length of buffer (maximum writable NDEF...
Hello there,
I have developed a board with nRF52840 and a sensor. My hardware and tools setup is:
SDK: nRF5_SDK_for_Thread_v0.10.0_e1c3d11
Thread version:OPENTHREAD...
Hi, I'm using evaluation board nrf52 (nrf52832) and using SDK 13 (nRF5_SDK_13.0.0_04a0bfd) and programing it using eclipse. Here is the code:
Someting is not working and...
I am able to disable the reset function of P0.21 by erasing UICR register and undefining CONFIG_GPIO_AS_PINRESET .
Still i can't set P0.21 as output and set it to 1.
According to the User Guide,
After each byte has been sent over the TXD line, a TXDRDY event will be generated.
When all bytes in the TXD buffer, as specified in the TXD...
