I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Do the LED drivers on nPM1300 have any ability to control either current or do PWM dimming? led_set_brightness() seems to not do anything and from the datasheet its not quite...
We have an nRF52833-based board, software is based on Zephyr and Nordic SDK 2.1.2. One of the SPI interfaces connected to external flash (Winbond W25Q80DVSNIG) Board is battery...
I have successfully implemented an interrupt-driven method to read data from the MPU6050 sensor on the NRF52840, and it functions as expected. However, I encounter an issue...
Hi Nordic team,
The LTE link monitor app is not showing up in my NRF connect for desktop v3.6.
What would I need to do in order to add it?
Is there a http link you...
I have written the code to test the RSSI signal, and the segger shows the result on the debug terminal, However, the debug terminal can only show first 500 data, the first...
Hi,
I have installed NCS 2.7.0 using the nrf command line tools, and followed the tutorial to install the NCS VSCode extension in VsCode. However, when I compile the Matter...
After I flash my code,I get imformations as follow:
*** Booting nRF Connect SDK v3.5.99-ncs1 *** ***引导nRF Connect SDK v3.5.99-ncs1 *** ***引导nRF Connect SDK v3.5.99-ncs1...
Dear Sirs!
I used SDK 12.2. Product was developed some years ago and now I am working for upgrade. One of new features is UART. I faced very strange problem.
I send...
Hello,
I am developing a HID device with DFU OTA and would like my customers to be able to upgrade this product independently via DFU OTA in the future. I would like to...
Hello Everyone,
I would like to interface the Accelerometer to nrf52810 via TWI pin P0.06 as SCL and pin P0.09 as SDA. I have to read the accelerometer data and send over...
Hi Nordic I am transmitting the dmic stream from nRF5340 dk to nRF5340 Audio dk. But I am not hearing the nRF5340 Audio Dk. Getting below Wrn's How can I hear the audio on...
Dear expert.
one of my clients manufactures medical devices.
as you may know, medical devices need to special certification depending on the country, such as North America...
Hoping someone can point me towards some guidance on how to properly enable, configure, and build mbedTLS options on the nrf52840.
I'm currently using Zephyr 3.6, with the...
Hi,
I developing an Hearing aid accessory with nrf5340 audio and STM32.
I do not have external flash so I need to use the nrf5340 internal flash.
I'm using the 2.5.0...
