hi support team,
when i testing wifi location, i found out one problem:
nrf_cloud_rest: Failed to encode location request, err: -12
that is this code in nrf_cloud_rest...
We need to set a GPIO pin in MCUBoot to activate an external USB hub chip so the USB DFU will work. I would like to do this with code in our project rather than directly modifying...
According to the nRF52832 Product Specification, “A step increase in supply voltage of 300 mV or more, with rise time of 300 ms or less, within the valid supply range, may...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-3-dfu-with-external-flash/
I have this exercise...
Hi,
I noticed in the nRF54L QFN48 reference design, for the NRESET pin, there is an RC filter (1Kohm series R and 3.9pF shunt cap). What's this for and is it necessary?...
Hello,
I am using a nrf5340 dev kit. When I use SPIM the output from the pins gives the correct hex values but the output's amplitude is only around 100-200 mV. I know that...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hello,
nRF5SDk16.0, Softdevice v.7.0.1, device nRF52840.
We using manufacturer specific information in the advertisement data. Here are the set values:
The data is...
We have a PCB production with bug where AC13 (P0.18) accidently has a via shortenede to GND plane on internal layer. Thus nRESET is stuck low and cannot be pulled high without...
Hi,
I modified the LBS service to experiment sending more than a byte of data.
On the peripheral side, modified from ble_peripheral/ble_app_blinky
typedef struct { uint8_t...
I'm using visual code for my development. I've tested a basic hello world app, this works fine so c/cpp is correctly installed.
I'm now testing a basic app, but I'm getting...
Hi Team,
For our development we are using the nRF52840 soc, We need the some example code or some project which will explains the Usage of RSA algorithm and supported API...
Hello,
I am looking at the ble_app_buttonless_dfu/main.c
This implementation is initializing the queued write module. Is this required now for DFU operation? We currently...
Hello,
For some reason whenever I try to pip install pc-ble-driver it will only ever install version 0.11.4. This causes a problem since I need the nrfutil library and the...
I sent some nRF9160 prototypes down to a CTIA certified test lab in North Carolina to do carrier TRP and TIS testing. When they add their test sims they seem to be unable...
Dear Sir,
I am new in embedded.
I start work on nrf9160.
I have to acquisition periodically through mqtt protocol, a data, with total space of approximately 30 kb, and...
I have installed SEGGER Embedded Studio for ncs sdk. I have installed everything else required to use NCS sdk.
From the command line at ncs/zephyr, I can successfully run...
Does Nordic recommend a specific version of SES? Should I just download the latest version direct from Segger or do I need a special version of SES to have full compatibility...
Hi Guys,
I was able to connect a second uart to the evaluation board and receive over uart.
however I didnt find an example of how transmit a buffer over uart.
is there...
Hi, we have a product that we want to update with new fuctionality, We use latest S110 for NRF51822 and would like to have more than 2 ppi groups useable.
In what scenarios...
Hello folks I have been struggling for some time with the driver for the MCP23S17 in Zephyr. I have already tried this code: https://devzone.nordicsemi.com/f/nordic-q-a/64024...
Hello I am developing a device that uses BLE.
User will connect bluetooth directly the first time they launch a custom app, and they will try to connect automatically the...