Good day,
I've developed a board with a MDBT50Q on it. I'm using the Reg0 DC/DC and LDO Mode Disabled reference circuit ( https://www.raytac.com/download/index.php?index_id...
Hi,
I have the issue that my Zigbee device reports the error "Production configuration is not present or invalid (status: -1)". I followed the guide from this( https://docs...
Hi,
I am using an nRF52840 as a Zigbee NCP. I have built the firmware myself using nRF Connect, and I am also running MCUBoot. Sometimes after some usage, the chip starts...
Hello everyone,
I am testing out I2C on the nRF54L15 for a custom PCB project.
I first tested a simple mpu6050 sensor on &i2c21 on pins P1.11 for SCL and P1.12 for SDA...
I have a bit of an unusual use case where the nPM1300 is quite ideal but need to use an external charger for the battery instead of the internal charger. The nPM1300 fuel...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
Hi,
I am trying to receive BLE advertisements on Ch38 (=2426MHz) without using SoftDevice, i.e. with direct register access. However "EVENTS_DISABLED" is very rarely called...
Nrf52832 based on sdk14.2 development as a slave, when linked with the iPhone, pairing and binding, and then get ancs service; and Android phone connection, direct communication...
I am working on a project working with remote connectable beacons. One of the easiest ways to save power in these applications is to reduce advertising speed, however, this...
Can anyone give me a tip on porting the code below, which works great in sdk12, to sdk14? I'm using the nrf52832 and the ble_app_hids_keyboard example and need to get a real...
Hi, I'm kind of a newbie, haven't had much experience with embedded outside of arduinos etc.
So I started to look at this: https://learn.sparkfun.com/tutorials/nrf52832...
for sdk15.0, SES,
is the twi_scanner example known to work with nrf52810?
getting errors,
undefined reference to nrfx_twim_init, nrfx_twim_enable, nrfx_twim_xfer
Hi,
I am studying the GPIOTE example from SDK 14. I did some modification adding other led and doing the leds blinking in differents times (LED1 blink each 1 sec and LED2...
Hi,
The nRF52832 does not support Long Range and i was wondering if the use of "RADIO_MODE_NRF_250KBIT" would increase the range. My application is a mesh network.
Do...
Hello Everyone,
I am using nrf51822 with S130.
Currently I am using arduino following this repo to program nrf51822 and its working fine. However, I want to shift to keil...
Hi there
For test purposes, I first implemented a simple serial reading & parsing function in polling mode of a gps device (sending @ 1 Hz).
Everything works fine when...
Hello,
i am evaluating the nRF52840 on the nRF52840-Preview-DK. I have connected an ADC to the devkit via SPI and my code reads data from the ADC via GPIOTE, PPI and SPIM...
We've got two SPI slaves that we need to talk to with the 52840 (PCA10056 dev kit for now) using SPI Manager. In the initialization of these devices, I'd like to use nrf_spi_mngr_perform...
when I use flash to storage my data,I call the fds_record_write(&record_desc, &record) ,and it return success,but my machine run err, my ble broadcast is missed.I used the...
I'm trying to understand what is meant in section 5 of the BLE on Android primer: "The peripheral device should disconnect itself when it gets disconnected by the client....
Hellou, I am developing application which need data array store to flash manager. I used for some function for storing data (nrf_fstorage_init(), nrf_fstorage_erase(), nrf_fstorage_write...
