Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
I tried building ' pca10040 ' configuration of " nrf52-mpu-easydma-using-gpiote-and-registers " example from " https://github.com/Martinsbl/nrf5-mpu-examples ". The following...
Hi
I am working on nRF51-DK with Mbed IDE & used PWM example code from link : https://os.mbed.com/handbook/PwmOut
When enabled PwmOut, PWM signal is observed on the oscilloscope...
I would like advice on whether the following is a valid ble transaction.
We have a product with the nrf52 in it running sdk 12 and softdevice 3.0. This is setup as a a peripheral...
Hi,
I'm using nRF5 SDK v. 14.0.0. I'm trying to pass a context pointer to the NRF_SDH_BLE_OBSERVER macro, but am running into compilation errors. I want to do something...
Hi,
I'm building a project with nRF52832 dev kit and the SHT10 temperature and humidity sensor, I'm searching for a library/example project of this sensor and the nRF52...
I'm planning to make a custom board using Thing52, following the reference desing. I have some questions (1) Can I use nRF52840 instead of nRF52832? (2) Do you provide an...
To reduce power consumption during sleep I have to completely disable the UARTE0. This is done before sleeping by :
NRF_UARTE0->TASKS_STOPRX = 1; NRF_UARTE0->ENABLE = UARTE_ENABLE_ENABLE_Disabled...
We are using Bluetooth Developer Studio along with Nordic's code generator plugin (Nordic Semiconductor nRF5 1.3.0 SDK 14.0) for our project.
We've made a couple of improvements...
Hi!
I got an error while compiling the proxy client example in BLE Mesh SDK V 2.0.0 as The object file build/light_switch_proxy_client_nrf52832_xxAA_s132_6.0.0_Debug/obj...
HI al
I have a bicycle computer (A) host (SDK 12.1 51822QFAC S130-V2.0.1) and a slave device (B) for measuring bike speed and cadence (using 2032 batteries). 1. When the...
Hi, I was recently asking about OPUS - https://devzone.nordicsemi.com/f/nordic-q-a/32875/how-compile-opus/128181#128181 . Now I am able to run encode on audio data and decode...
Hi
We have a nrf51 dongle for use in a school prosject When the nrf51 dongle is connected to the USB slot in a computer it boots fine without holding the button when powering...
On the Getting Started page, I do not see the USB described in Step 7. I do not see any device. The LEDs flash and the buttons light up LEDs 1-4 as described.
Thanks
Hi,
I'm using nrf_serial 'object' in order to communicate nRF52832 with an external device.
As I work in non-blocking mode I need to verify if there's available space...
