Hi, I am using nrf52840 , nrf connect sdk 2.6.0 I am using spi_transceive() to send and receive the data from sensor I read in Nordic Academy nrf connect sdk intermediate...
I hope this message finds you well.
I am currently working on a project using the nRF9151-DK Evaluation Board and have been testing GNSS functionality in various environments...
Hello,
I am a developer/maintainer for the RF24 Arduino library at https://github.com/nRF24/RF24
I've found in some cases, the R_RX_PL_WID register returns 0 while the...
Using VS Code and latest version of SDK and toolchains. I have created some custom board definitions and placed them in a seperate directory. The directory is registered in...
We get the following assertion during startup if we include uart2 in the DTS.
*** Booting My Application v2.1.0-dev-ae1ee57f3906 *** *** Using nRF Connect SDK v3.0.1-9eb5615da66b...
hi team,
i am working external adc with the help spi communication, now adc working fine with the SDK version 2.6.1 , if will make or change any other SDK version like Ex...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with two specific exercises: l2_e3 and l4_e1 . Other...
Nordic has provided a good SPP implementation over BLE.
devzone.nordicsemi.com/.../
However, will it raise power consumption and cause BLE to lose its low-power characteristics...
When trying to do a direct advertise massage ( sd_ble_gap_adv_start ) I get error code NRF_ERROR_INVALID_STATE (Invalid state, operation disallowed in this state). This is...
Hi Team,
In my application UART is used.
I need to send parity bit based on particular responses that I need to send to the device
connected to UART.
Can I change configuration...
Hello,
I'm working with timeslot API (basing on github.com/.../observer) . I have an advertising and active scanning running concurrently. However, I want to completly...
I am using nRF51822 to generate 3K HZ PWM signal for a buzzer.
I read other people's question and try it.But as far i can't solve this issue.Please help.
At first i use...
Hello,
I just ordered a shiny new nRF Beacon from Mouser. The beacon is version 1.1.0 advertising "DfuTarg", so I am attempting to flash the application file that comes...
Enlight of the increase in 8.0 SD size, I am concerned that my application size may soon grow too large to utilize Dual Bank DFU. I know the actual size of the .Hex files...
修改Device_Name.jpg
After programming, the device name cannot be changed.
Is there any solution that can achieve?
I know that I can change the paramter from the function...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
The Master Control Panel will be able to keep the connection for hours and hours.
But when I am using the iPhone 6 to do the test, after connected, it will also be disconnected...
Hello
I've been having some strange problems with my SPI and TWI bus. In my setup, I'm using SPI0 and TWI1. I noticed that, even though I'm not using it, that SPI1 was...
This seems to be a common problem after searching in this forum. In my case, I need to read from an I2C slave and send the data out in BLE. I have made it work without SoftDevice...
Hello!
In my application, I have to receive UART signals from another device. The problem is the signal comes inverted so the nrf51422 can't handle it. I thought in 2 possibilities...
In spi_master.h SPI_DEFAULT_TX_BYTE is define as 0x00.
This value will be used when sending dummy clocks, or just reading from SPI slave, or writing length is less than the...
