Hi,
I recently updated Nordic connect SDK and toolchain from v2.7.0 to v3.0.1. When compiling my application with activated CONFIG_BT_LL_SOFTDEVICE flag, I get this error...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
Hi,
I have set up the UART example with PCA10000 and PCA10001. Everything works fine but one strange thing is the time to send 100kB of data. See my times below:
38...
Hi !
On this thread devzone.nordicsemi.com/.../nrf51922-1 i've found someone introducing the new S130 softdevice for the nRF51822 wich allows the IC to be on concurrent...
Hi to all,
Ihave a problem with erasing flash on nRF51422 Evaluation Kit. When i click on Erase all button in nRFGo Studio everything is looking normal ( segger led is blinking...
I cannot download S110 to try right now. I have some 51822 Dev kits, but somehow I didn't get the product keys entered into my page, and the boxes are all gone.:D
When my application is running on the nRF51822 (e.g. the hrs example from the sdk), I want to stop this application (e.g. at a breakpoint), investigate some memory and than...
Hi,
I've started developing some test applications for the nRF8001 to better understand all the ACI libraries and improve my knowledge of the chip.
I'm experiencing some...
Unless manually set the value of bond_init_data.bonds_delete to true in the function bond_manager_init to clear bonded masters, I end up in the HardFault_handler. The last...
I'm trying to just set up a Timer for 8 MHz frequency and have that output on a pin. It seems simple but I'm having some problems (the frequency is a lot lower). What am I...
Hi everyone,
I've just started to develop software for NRF51822 - Bluetooth Low Energy on the Evaluation Kit. I managed to connect the development dongle and evaluation...
Based s110_nrf51822_5.2.1_softdevice.hex and nRF51 SDK v. 4.4.1
When scanning iOS, why not click pair on the iOS side and NRF51822
connected on? whether the pair can be...
Hi,
I'm planning a hardware solution and I need a BLE IC capable of act as a master and a slave, not at the same time, but with the possibility to change it's role by software...
I used nrf8001 to implement ANCS.It working fine.But when it disconnect for a while and reconnect(reconnect successed).I found Iphone can't send any ANCS message to nrf8001...
Hi, I would like simplify the nRF24AP2-8CH signal RF output using a Balun with a chip antenna.
What is the best way: the 2450BM14A0002 from Johanson, the BAL-NRF01D3 from...
