Hi,
I assume this would apply to most new boards - but I am finding that the build time since upgrading to newer hardware has increased significantly. Perhaps due to sysbuild...
I am currently using ncs 2.9.0 on a custom board using the internal ldo and internal clock settings. It is a simple project where I take and indicate an adc and internal temperature...
Hi! I am designing a nRF54 based motion tracker that has an IMU onboard which can take an external clock signal for improved timing accuracy. Initially I had thought of just...
Dear All,
I updated Toolchain and SDKs to last version v3.0.2 and I'm going to add build configuration as suggested here How to create and build an application .
My board...
Hi, I have created my own hardware with nRF54L15 – 2xLED, 2xPWM, and Radio (BLE). I am trying to create a custom board using the graphical wizard. LED and PWM seems to work...
I have an external GPS module connected to an nrf9151dk over UART. The module is correctly powered, and sending messages over its tx pin, which has been confirmed by attaching...
I´m trying to change the installation path of the Nordic Power Profiler as I´m running out of space.
I have about 9GB left, but when trying to open a captured file, Power...
Hi,
I am trying to use the DFU example provided in SDK 5.1.0. I have built the example using gcc 4.7.x, and i am also using softdevices 5.2.1. The DFU example has been...
Hi,
I've the need to write a characteristic value of 65 bytes, from my central device (iPhone/iPad) to a nRF51822 peripheral device, so I was looking at this document for...
Hi, sorry if this is a dumb question. I've just ordered some development kits and maybe that will answer the question, but i'm being a bit impatient!
I want to put an nrf51422...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi all,
In my project ,I use the SPI to communication between nRF51822 and STM32,but I don't know
how does the heart_rate data transmit to BLE stack.
I am confused...
We have a custom nrf15822-AA board flashed with the S110 (6.0.0) and our application. It has a 32khz crystal. It is connect to our (Mac) development systems with a SEGGER...
I use 51422 with ANT function. When I set a command like "sd_ant_channel_unassign", how can I get response from on_ant_evt callback?
I need to do something after ANT unassign...
I have a nRF8002, I use nRFgo Studio to program the board, and Master Control Panel on Windows to check it board values.
I would like to be able to recognize when the nRF8002...
As the network speed is so low that I often cann't access www.nordicsemi.com, especially on weekends.
Could you tell me the reason?
Note:
At the time when I can...
I am successfully communicating through nrf 8001 chip and i using this module. Now i want to write services and characteristic to this module through iPhone after getting...
Hello：
1.
I used connect Master Control Panel and ble_app_cscs services see the following received some data not understand do not understand, here's UUID I did not see...
Hi all,
I have various questions regarding the softdevices, memory management and power consumption of the nrf51822 chips.
The project we are working on will need to...
I am working on nRF24LE1 boards. I am trying to talk between two boards. I have loaded "enhanced_shockburst_ptx_nrf24le1" and "enhanced_shockburst_prx_nrf24le1" on two different...
I saw an ANCS examples in sdk5.1.0(softdevice=6.0.0), and then I put this example to port to sdk4.4.2 (softdevice=5.2.1) and the example worked perfectly. But when I put the...
Hello,
I have set up my project to use the DFU bootloader to upgrade the application. When my application is running it can be sent a command from the central device to...
