Hi.
I am using SDK v2.6.0 (Toolchain v.2.6.0). When I open VS Code (v1.91.1) I keep getting this warning -->Bad CMake executable: “”. Check to make sure it is installed...
Good day,
I am trying to combine gzll, USBD HID and USBD CLI with SDK 17.1.0 and nrf 52840. GZLL receiving input, send to USBD HID, USBD CLI output logs and debugs.
Below...
I am at my 15th attempt to download the SDK from Vscode Nordic extension. It keeps failing midway, sometimes after 30mins, for various reasons that are probably related to...
Build environment is the nRF SDK Connect for VS Code extension with ncs 2.3.0.
I am trying to accomplish DFU over UART with mcumgr serial console in which primary slot will...
I have seen a few posts including:
Change advertised name (Bluetooth) - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com)
NCS bt_set_name() - Nordic Q&A...
Hello,
I am scheduling an RSSI measurement operation using DECT PHY firmware v1.0.0. The parameters used for scheduling the operation are: - start_time = 0 - carrier = 1677...
Hello support team, i have an issue regarding the i2c configuration on an nrf52832.
The Setup is:
EvalBoard nrf52dk_52832
BME280 Sensor attached via I2C
NCS 2.6...
Hello, I would like to ask about the problem of how to implement SOC shutdown in NCS. 1. In V2.6.0, CONFIG_PM cannot be enabled, it will prompt that there are dependencies...
Hi there!
I was just trying an example of DFU over UART from the new nrf Connect SDK Intermediate course using the NRF9161DK but I'm unable to disable the mass storage device...
Dear sires,
Would it be possible to let you answer the following question?
In nRF5340 SDK, does it use CMD20"SPEED_CLASS_CONTROL " in SPI write sequence to ensure minimum...
During some operations like factory reset, or during a hardfault we want to check if the softdevice is enabled and disable it if it is enabled before continuing with further...
Hi,
I want to use BLE mesh to reach my application, the requirements below.
I have a root node and need to send the custom data to each client node and need to read...
Hello! I was building a custom board and tried to build the project for my board but it gives an error: === child image hci_ipc - CPUNET begin === loading initial cache file...
My understanding is that Singled-linked list built in to zephyr... https://docs.zephyrproject.org/latest/kernel/data_structures/slist.html But, I don't quite understand how...
Hey I've got this project that requires two buttons. In normal mode, these buttons react to the Ready pin switch signals. when it goes into sleep mode (where it controls other...
when i use vscode to open nrfconnect,it's always waiting there and can't start.as the same time,i can't open vscode by nrf connect for desktop,it will report the error ,but...
I am using ESB communication.
In general situations, data transmission works well. However, issues arise when multiple PTX devices transmit simultaneously.
It's understandable...
Hello,
I use Nrf52833DK running nRF Connect SDK (NCS)
I want read and write BLE MAC device address no matter it's the public one or static one.
Now i know bt_read_static_addr...
hello,
I'm try to fit my application to Android 14.
my application implement nordic DFU library ( for nrf52833 running freeRTOS firmware SDK 16 ) version 2.5.0
while...
Hi
I'm using the PDM module to capture audio through MP34DB02 PDM microphone ( here 's the datasheet). I set the clock frequency to default 1.032 MHz and a gain of +4 dB...
Hi there,
The nrf5340_audio application provides a -DFILE_ SUFFIX=fota overlay that adds FOTA capabilities to the application. This FOTA is introduced via Sysbuild configuration...