Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Hi,
We have developed firmware for a custom broad using the nRF52832 with 512kB flash, and our firmware currently uses 48.5% of the flash.
We are using Zephyr and version...
Above is the trace and the commands inserted. We were unable to get a response using the at+cops? command. Both SIM cards were active that we tested. We tested band 12. Could...
I would like to know more about the TLS 2K packet limitation in the nRF Connect SDK.
Is there a way to not be constrained by this limitation. I've seen some posts about...
Hi,
I am using nRF5340 DK and nRF SDK V.2.6.1 for my project
I am following the link;
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson...
Hi,
I'm hoping you can help.
I am using the CENTRAL_UART and PERIPHERAL_UART to evaluate the nRF52840, and using a terminal program works fine.
What I want to do is...
Hi all,
I have a problem that seems very simple, but I cannot make sense of it.
I have a simple setup on the NRF52840 DK that senses a rising edge on pin 1.00 and...
I am trying to write tests for my code using CppUtest. I know the platform has memory leaks detection support. it seems that everyting is set up correctly to see the results...
Hello,
I am starting with the nRF Connect. I got a nRF52840 DK and I am following the 'nRF Connect for VS Code' YT series.
I got as far as part 5 (debugging), but I cannot...
Hi all,
SDK: NRF Connect v2.5.0 We've made a custom PCB with the NRF9160, and we have made a custom board configuration for it.
Our issue seems to appear when trying to...
Hello,
I have a mosquitto broker running on my pc. I want to connect and published to this broker through nrf9160.
The issue that I am facing is that prj.conf file only...
I want to use RTT log to output some data, but the data is output. 6 bytes in a line, but the first byte is an independent line, and the next 6 bytes are a line, staggered...
I would like to enable and configure the high power mode on the DC to DC converter in the nRF52840.
I am looking for the device tree source entries and the necessary entries...
Board: nrf7002 Project: matter_light_blub OS: Kubuntu 22 Toolchains: v2.6.1 SDK: v2.6.1
I am developing with the nrf7002, and my current setup involves using a Samsung A54...
Hello,
Is there examples of paring,bonding and whitelisting?
The pairing and bonding mode is static password.
It is best to have examples of the central and the peripheral...
