why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hello Nordic Support Team,
I am trying to upload firmware to my nRF54LM20B-DK using the nRF Device Manager application on my mobile phone .
For this test, I started with...
Hi!
I'm testing ubidots, which require a 35 character long username to connect with MQTT. This fails, and mqtt_connect gives me error -12 ENOMEM. The same code works fine...
HI,
As stated in the topic I have found several misalignments/issues in the following setup:
NRF Connect Desktop (v5.3.2) NRF Connect Desktop DTM (v3.1.4) NRF CONNECT...
nRF54L15: system clock stops permanently after a GRTC compare event is lost
Disclaimer
Claude Code (Opus 5) was used to assist with this investigation and with the drafting...
Hi, I just started evaluating the nRF93M1 DK (LABA version) and have questions about the firmware version.The AT+CGMR gives "mfw_nrf93m1_1.4.1", which seems to be a bit older...
We're based in India, developing a custom hardware board, and need to test CAT-M1 connectivity on-device. Since CAT-M1 coverage is limited in India, we're planning to travel...
I need an architectural guide and recommended workflow for setting up post-production (in-field) cryptographic key provisioning on Nordic nRF devices (nRF9160 and nRF9151...
Hello,
I have a project based on nRF9160, that uses nRFCloud over CoAP. It uses SDK 2.8.0, with functions such as functions such as nrf_cloud_coap_json_message_send() and...
Hi, we would like to create a kind of game using 2.4Ghz emitters . The 2.4Ghz USB Dongle emits and the mobile phone detects the frequency + embed unique ID/code so we confirm...
Hello,
we are currently developing a device based on the nRF5340 using LE Audio.
The device streams audio to a smartphone, where the corresponding Android application...
NRF52840
We are using NCS v3.3.0, however this issue occurs also on NCS 3.0.0.
When using the SoftDevice Controller stack. ie MPSL etc enabled, at times we enter SYSTEMOFF...
Excuse me.
When the customer uses the nPM1300 EK for battery charge‑discharge profile logging, after charging completes at 45 °C and the USB cable is unplugged as prompted...
Yesterday, I upgraded to nRF Connect for VS Code extension version 2026.6.2030 and restarted VS Code, and now no matter what I do, the 'Flash' button in my project just pops...
Hello, I am looking at pages 871 and 872 of the datasheet for the QFN48 package, but I’m not sure I understand correctly. Could you please tell me which GPIO P0 pins can be...
