hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
I only want to know if it is possible to enable and configure the Server Name Indication (SNI) for DTLS on BSD sockets and CONFIG_NET_SOCKETS_OFFLOAD=y (not using...
Guys,
I am able to successfully build zephyr/samples/hci_usb for nRF52840 USB Dongle, but the same sample code fails while trying to build for nRF9160-DK
Works as expected...
Hi! I'm working on a mobile application that interacts with an NRF52 device. We'd like to be able to programmatically reset a device stuck in DFU mode so that it tries to...
Hi,
I have never used Nordic devices before so apologies if these questions are answered well somewhere, I just can't find the best article anywhere.
The project I am...
Hi, I have built a BLE-enabled sensor that is capable of measuring the air flow and volume passing through a pipe. A new sample is generated every 10 ms.
In the language...
Hi,
I am currently developing a project using ultrasonic sensor for measuring level. So I was migrating library from development kit to nrf sdk code. I am using Keil uVision...
I am trying to interface winbond flash with the 33 board using ncs and VS code , I am able to get the code to compile and not receiving any errors , it is working and no matter...
I'm trying to use `bt_hci_register_vnd_evt_cb' to register a call back to process vendor specific hci events.
below is my prj.conf
my callback function for testing...
Hello, Everyone. Now I am trying to develop a BLE mesh firmware using my customized nRF52832 board. I followed this tutorial https://youtu.be/ufjv2NaLfN8?t=1745 But I can...
Dear Community,
Why is the nRF Connec SDK is mixing up path separators '\'and '/' when building under MS Windows 10
with nRF Connect Desktop 3.12.0 / toolchain manager...
I've been following this blog post to increase BLE throughput for my application: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection -...
I'm using nRF5340 DK for BLE, AoD (Connection). I am also using the TX example from nordic. I can add extra antennas to the ant_patterns[] (up to 17), with no errors. I also...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v2.0.0 I'm testing NCS 2.0 with Android 12. Making pairing with Android, I call two API when connected.
bt_set_bondable(true);...
Hi there,
I have a problem to implement the SPIM in the Network core. I cannot detect any signal from SPI_SCK & SPI_MOSI by oscilloscope and logic analyzer (no signal from...
