Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
I used 9160 to develop a project for the customer. During the project test, sometimes the data line or clock line level of I2C was abnormal due to hardware reasons. I wonder...
Hi, TF-M is supported and used on nRF5340 through Zephyr and we are having no troubles to run it and use it. Thus, we have had some discussions regarding the Secure and Non...
Hello,
I have interfaced the ble_hid_keyboard with uart using nrf52840-Dk in SDK 17.1.0. I am getting data to BLE_HID over uart, but i am not getting uppercase letters when...
Hey Nordic,
I use,
pca10056
s140
SDK 17.1.0
The following are the logs taken from PuTTY:
You can download my project from here . It is based on "ble_app_uart...
I'm running into an odd problem... I'm using a nRF52832 development kit and pc-ble-driver-py to write tests against our custom services and characteristics, and I just hit...
Hello everyone,
I am working with the latest Zephyr NCS 2.0.2 SDK to develop a BLE App with a nRF52840 Soc.
The device is going to produce a very low data rate, so I want...
I am using Nordic seriaization with nrf52480 as connectivity chip and a custom M4 board as Application chip. After 5th connection, the advertisement is not starting. While...
Hello team,
I am trying to build an audio LE application where I require a stereo output and microphone input. As an initial part of the project, I am trying to connect...
Hi,
I'm developing firmware for nRF52840 device (Acconeer XM122), and I'm trying to use fstorage library to write some data to flash.
SDK version 15.3.0, Segger Embedded...
I'm currently attempting to get the nRF 9160 to enter PSM mode when not transmitting along with the asset_tracker_v2 application just so we can do some power consumption measurements...
Hi Dev Zone,
We have an existing design that includes the Espressif ESP8266 Wi-Fi MCU and we would like to add an nRF52 to the design. Our preference would be to add the...
I'm using NRF52833 with SDK v16.0.0 along with mesh SDK v4.1.0. I want to know if it's possible to write data which is not word aligned into the internal flash (For example...
Hi everyone,
I started working on nordic nRF52832 DK and tested out some examples. I think i am done with the examples now and am looking to write my own code apart from...
Dear Members,
How can we determine the first ANT message from my transmitter ?
We saw from ant_parameters.h,
Which variable is being used ?
Kind regards...
Hi,
Today I found that after I OTA my board, it runs well at first. But when I reset it, it will run old image again.
Before this OTA, my board has gone through many OTAs...
