There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi,
I have this development board https://www.nordicsemi.com/Products/Development-hardware/nRF9160-DK . I would like to use development board as nb-IOT modem and other MCU...
I am just getting started with the Nrf52840 dongle and trying to flash a few examples from the SDK. I was able to flash the "blinky" example just fine using the programmer...
Hi,
I have been trying to interface GSM modem with nRF52840 using LPUART (nRF Connect SDK). I have used below pins for connections:
nRF52840 - GSM
P0.21 (TX) - RX
...
Hello,
Now I am developing firmware for nRF5284 DK, and the one of the requirement is the voltage keep in 2.1V.
Is there any possible I can modify the voltage to 2...
Hi guys,
I'm thinking of implementing consumption optimization on a system that runs on nrf52832 with S132 SDK 16.
The idea is to call nrf_pwr_mgmt_run() to put our...
Good afternoon,
I am working with the NRF9160-SICA-B1A-R module on a custom board.
Checking the functionalities with a software developed on a Thingy:91, I get the following...
Hi, I have recently upgraded to a new system with windows 11. I have been working with NCS v1.8.0 on last system and installed the same in new system. all the necessary installations...
I have downloaded the WS2812 driver example and have successfully been using the nRF52832 DK to control these lights with SPI. I am ready to start developing on a custom board...
This was driving me crazy. nRF Terminal extension in VS Code just silently fails. I was able to use the JLink Viewer app so I knew RTT was working correctly.
I then looked...
Hi, I am using nrf52840 to senda imu data over bluetooth to computer. For the transmitter i am using NINAB306 with integrated PCB antenna as a central i use nrf52 dongle....
Hi,
while switching to the nRF Connect SDK, I cannot program anymore my ANNA B112 (which is a nRF52832) using my nRF52840-DK as a programmer.
The following are working...
i m using nrf5340 cutom board, so i m using rtt logging method using jliink rtt viewer , to see logs .
so, when i am going to project section at top in embedded segger studio...
Hi, There, I use 52832 to develop a HID touch(single point) device, it can work on android & windows, but can't work on iphone13(ios15). It can connect to iphone, but no touch...
Greetings,
When trying to perform an http GET command over LTE-M (using the "Curl" MoSh command, to trigger a http download of a 500Ko or 1Mo file) after a few successfull...
I'm using three low power PWM instances driving three separate IO pins open an nRF 52810 and need to be able to re-configure each of the channels on the fly to select opposite...
