Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Hi! I've recently received my Thingy:91 and wanted to get it up and running. I followed your video ( https://www.youtube.com/watch?v=xQ7hDzRULJQ ), although did not see the...
Hi,
I am testing direct advertising with two nRF52-DK. One performs a direct advertising and the other scans for the directed adverts. Unfortunately, the scanning device...
The NRF52840 specifies a 20%, 10uH inductor for the integrated DCDC convertor. Why is the inductor value so large? This switcher runs at 8MHz, which usually means something...
I have been tasked to use out-of-band authentication for the nRF5340 using the NRF Connect SDK (Zephyr based). Is this feature supported within the SDK. Is there an example...
HI
I use SDK 17.0.0 in NRF52833.I test uart by example project ,the dir is \examples\peripheral\uart\pca10100\blank\arm5_no_packs .
Modify the baud to 921600 ,and send...
Hello,
I am attempting to update a custom C# application that is utilizing the NRFJPROG dll. We are hoping to add compatibility for multiple programmers connected to the...
I used ble_app_hrs Demo to test bonding. However, I have been unable to bpnd successfully. I'll give you my bonding parameters.
#define SEC_PARAM_BOND 1
#define SEC_PARAM_MITM...
Hi,
When I increased FDS virtual pages to 50 pages and after download to device, and then used Programmer to read flash to get the images shows more longer than before,...
Hello,
I am a beginner in Zephyr, I am using the nRF 52840 DK board and I want to connect the HX711 module I have implemented nrfx_timer to make it possible to give pulse...
Hi,
I working on nrf52840 DK with nrf5 SDK17.
I tried to find out the power consumption of the peripheral(TWI/SPI) from the nrf52840 PS v1.7 document but it is not mentioned...
Hi,
I have combined a couple of examples in order to achieve the following on a custom nRF52810 board:
Count the number of pulses on a pin (using TIMER1)
Read the...
Hi, I am using P822601 board (with nRF9160 chip). Sample project "Serial lte modem" (SDK 1.8). Faced a problem related to the inability to connect to the MQTT broker when...
Hi
We want to run the AT command as the following, the response is always ERROR.
signal generator: CW, freq=param1-120KHz=1804.88MHz, power: -100dbm
AT%XRFTEST=4,1,3...
Hello
I need more flash and ram so I change the sdk to 13.1, but when I enabled the softdevice the log advice me use more ram.
How can I use little ram as s132_nrf52_4...
