Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I am using Nordic's NRF_SDK_For_Thread_and_Zigbee_4.1.0.
In that example/thread/ncp, I want to build NCP firmware for uart.
Original uart pins for rx and tx are 8 and...
Hi,
I have nCS installed and when creating a project in nCS installation directory (default path), then i have option to choose "Configure nRF Connect SDK Project" from...
Hello,
For my board i would like to remap uart to pin on GPIO PORT 1.
Current:
&uart0 { status = "okay"; current-speed = <115200>; tx-pin = <20>; rx-pin = <22>; rts...
Hi,
We have a requirement to connect a SPI device to each SPI interface present on nRF52840, and we want to write to those multiple devices in parallel. Is there any API...
Hello everyone,
I would like to run the ANT examples "ant continuous scanning controller" and "ant scan and forward" on my nRF52840DK(PCA10056) boards however it only supports...
Hi,
We have a device based on nrf_52840, SoftDevice_132_3.0.0 and SDK_12.3.0, using BLE for communicating to a PhoneApp and UART for communicating to a washing machine...
I'm writing an application for the nrf5340 with nrfConnect v1.6.1,
I've been able to do the FOTA upgrade through BLE with the example smp_srv located inside zephyr/samples...
I recently got the nRF52840DK and have been able to build/flash a couple simple samples. However when attempting to try the OpenThread CLI example on tool chain v1.6.1 and...
Hi,
cannot run pc-nrfconnect-launcher v3.7.1, built from sources.
```
$node -v
v12.22.5
$git clone https://github.com/NordicSemiconductor/pc-nrfconnect-launcher...
Hi,
When I want use nrfjprog to program my NRF52, I have a problem.
This why I write to program my nerf : nrfjprog -f nrf52 --program _build/astronaut.hex --sectorerase...
Hello,
Is there example code on how to get NRF_SAADC_INPUT_VDDHDIV5 working? When I do nrfx_saadc_init(), I get NRF_ERROR_INVALID_STATE.
Same code works fine with normal...
I am using nrf5340 and icm20948 for our development. i had initialized things as shown in code attached.
this work fine for me. but when i am uncommenting rc |= inv_icm20948_enable_sensor...
Is there any guidance on zigBee OTA? What are the similarities and differences between ZigBee OTA and BLE OTA? Could you please tell me what I need to pay attention to during...
Today I received my first CMSIS-DAP debug probe (Pitaya link) and tried to integrate it into my development environment. Unfortunately, I must have broken my Pitaya Go (Nordic...
