This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
Hi,
I need to output a continuous 16 MHz clock on a GPIO pin on the nRF54L15.
I first looked at the GRTC clock output, but since the fast clock is divided by (CLKFASTDIV...
Hi, I am developing a program for the nRF54L15 with the DFU bootloader enabled. I would like to reduce the startup current.
I am using SDK 3.2.4.
The `sysbuild.conf` settings...
Hello,
I work on a zephyr project with the MCUBoot and two updatable images: custom firmware loader + TFM and main application. Update works over BLE. For testing I use...
Hi
I am planning to develop a product based on the nRF5340 DK.
Please provide a response to the following inquiries:
1. Is it possible to obtain the schematic and PCB...
Hello
I want to clarify something because there seems to be a lot of conflicting information on Dev Zone, and the nRF5340 DK documentation doesn't specify the following...
Hi DevZone,
I am currently working on a project that uses MCUboot (DFU over BLE) on the CPUAPP core together with a custom FLPR application.
I successfully got this working...
Dear Community, Hopefully an easy one: Is there anyway to make the flash programmer selection stick in nRF Connect for VS Code? Every-time I click on Flash to program a device...
I am using ncs v3.3.0, and since Partition Manager will be deprecated, I followed the migration guide to use DTS board configuration. I am using mcuboot in firmware loader...
Using:
NRF9151
TF-M enabled
NCS 3.2.2
I'm trying to find more space for my heap on the nrf9151 and I'm disappointed that with a minimal implementation of TF-M...
I ran into a couple issues with network core updates on NRF5340 when updating from 3.1.0 to 3.4.0 SDK. Problem 1) Network core updates are not backwards compatible with 3...
Hello, We have a question about the errata workarounds applied in SystemInit() in nRF5 SDK v16.0.0. Our firmware is split into two images: a boot application and a main application...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I have a pin on port 1 of the nrf54l15 that I am bitbanging for a custom tx/rx 2-wire protocol. I have already managed to implement the tx capability and I was hoping...
