Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
Master Control Panel shipped with MasterEmulator.dll, which could be called from C# to discover and communicate with devices.
With nRF Connect, MasterEmulator.dll is no...
Hi,
Edited, should have pointed out that I'm using the nrf52.
I'm using a simple setup with a MEMS-microphone, and tries to read data from it.
I have setup the DMA...
Hi, I'm working with nRF52832 DK, SDK 15 on Windows with Keil5. I create Multiperiherial Nus with peer manager and fstorage and it works, but after some connetions I get an...
<error> app: ERROR 8 [NRF_ERROR_INVALID_STATE] at the same line as
ret_code = ble_advertising_advdata_update(&m_advertising, &new_data, true); APP_ERROR_CHECK(ret_code);...
Hi, maybe it's time for my dream project to come true. I have one NRF52840 DK on the table, one desktop PC, one laptop (BT 5), one iPhone X (not mine, just for a case) and...
Hey,
I am new to this , i am using nrf51822 for development , as the documentation says i downloaded the sdk and i got the nrf5 dk and i am using the Segger embedded studio...
Having problems with nrfjprog and a custom board. I connected my custom board to the NDK via P20 and flashed a program to it. The program was a variant of the pwm_library...
dear
i am using this project as slave
\nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart\
this project as central
\nRF5_SDK_14.2.0_17b948a\examples\ble_central...
Hello all,
Almost giving up, I'm struggling to make my nRF9160 working. I can't use the LTE Monitor at all!
Tried everything, I think, and run out of ideas. All AT commands...
I have a custom board with nrf52840 with cr2477 battery (1Ah capacity). I was download firmware to board and after a week the battery voltage dropped to critical. In the firmware...
Hello everyone.
There have a scenario, nrf52832 starts a direct advertising , but the dest ble device is not bonded(it could be any other central device), when the dest...
Hi. I am developing the nRF52832 using the NRFX module of the SDK version 15.2.0. We convert the UART signal to RS485 and communicate with RS485 to the outside. RS485 communication...
Hi,
I'm using nRF52832 on a custom board and I have tried to run sdk example nfc_url_record, but it doesn't work.
I have tried to find solution among existing answers...
Hi All,
For my project I'm using NRF52832 IC and NRFsdk. I need 2 GPIO external interrupt to get notified. I'm able to configure both pins and able to see the trigger when...
Hello Dev-Community, I have modified the Thingy Firmware for a custom made board which has also the MPU9250 with TWI connected. Everything works fine, if i use RTT Viewer...
