Hello,
We are looking for a developer a single task project. We need to provide all of our developers with the same development environment, so we are looking for someone...
I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hello,
I am experiencing a critical failure while trying to program my nRF5340 DK using the nRF Connect for Desktop Quick Start app (v1.6.0). The process fails at the "Program...
I am having a recurring problem with NFC-CONNECT: build action. It hangs when building. Gets stuck with the following message in lower-right hand corner of screen:
The...
I have successfully installed west and zephyr, and I have successfully build a simple tflite-micro hello_world example, but it just generates the zephyr.hex file. SInce i...
I am using a dynamic BAS service. I have noticed that after a few bt_gatt_service_unregister() and bt_gatt_service_register() calls, the following error occurs: bt_gatt: Unable...
Hi, trying to directly build the solution for the exercise i get this error at the end.
The whole log-output:
Building l5_e1_sol west build --build-dir /mnt/df01dc22-f3bf...
Hi! I am trying to get the samples "Bluetooth: Direction finding connectionless locator" and "Bluetooth: Direction finding connectionless beacon" to work on nRF54L15dk. I...
Cannot program our nRF9151-SMA-DK, we have other boards and work normaly. This is the programmer log:
08:30:21.996
Initialising the bundled nrfutil device
08...
nRF54L15 - ncs 3.02 - toolchain 3.02
I changed my build settings from no sysbuild to sysbuild in order to use serial recovery and/or FOTA. I thought everything was OK until...
Hi,
For my university MEng group project, I am working with the nRF5340 Audio DK and Bluetooth LE Audio (LC3 over ISO).
My end goal is to stream audio from an nRF5340...
hi,
i'm a beginner for nrf9160DK so can you guys help me to how can i nrf9160 up and running for the first time. i'm not able to up and running with this video https://www...
I have a problem where the GPIO pin is not working as intended (it is constantly high but it should be alternating high and low). Via debugging I've ascertained that the problem...
Hello, I am encountering a crash in MCUBoot when using the following configuration:
MCUBoot as bootloader (SB_CONFIG_BOOTLOADER_MCUBOOT)
TFM configuration (build /ns...
I am encountering a build error while setting up a build environment. Can you provide assistance as to what the issue I am encountering may be? I am using VSCode on MacOS...
hi,
i'm stuck at lesson 3 exercise 1 in step 1 so i create an application with choosing option 1 create a blank application for this first task to print hello world and...
Exhausted everything. Here's the guts of the code. A task is called at 2Hz to push the value, which at 1024/s makes an event time of +512. I set the cumulative RPM to +1 for...
