When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi,
I have ordered custom board based on nRF52840 SoC couple of times from JLCPCB and that included assembling as well. Unfortunately, 90% of the boards had floating aQFN...
Hi,
I'm using the Bluetooth sample called Central HIDS and want to develop a feature that stops BT scanning after a few minutes.
However, during development, I encountered...
Hello,
I have a question regarding the consumption of the nRF9161 DK board when it is under the following conditions: MCU on IDLE, modem off, wake on GPIOTE input (event...
Hello, I am wondering - Is it possible to program BL651 Bluetooth 5 with nRF52810 using pca10040 development board with nRF52832 on it and using
BLE HID Keyboard and Mouse...
Hi,
I recently started upgrading an nRF chip on old SDK to the latest nRF Connect. The device has only one button and currently uses a static passkey (written on the device...
Hi! Firstly I am somewhat new to developing on nordic chips so I'd like to apologise in advance or any silly mistakes or oversights I may have made. I am currently working...
I am using NCS 2.6.1 and have programmed a nrf52840dongle (USB Dongle) with the build result of nrf/samples/openthread/coprocessor
The problem I am having is that normally...
Hello,
I was able to setup nRF5340 Audio DKs as gateway and headset, test the USB audio input and enable the Walkie Talkie demo. But in both cases I'm using I2S/analog headset...
I want to use the signing script as mentioned Technical Documentation (nordicsemi.com) , however, with NCS, this script is not automatically being picked up during the build...
EDIT: I thought I had enabled RTT terminal output in this proejct, which I had not. Obviously this will have an impact on my problems sorrounding RTT terminal output. So I...
Dear all,
I used till now an application to route BLE data over serial port through the dongle USB nrf52840, SEGGER IDE and 1.9.2 nrf conneck. All works well.
Now I'm...
I would like to confirm how to make nRF5340 Audio stereo.
The nRF5340 Audio source is mono, and to make it stereo I believe that it is necessary to convert the data between...
I have a project that was building, but now on restarting VS Code, I cannot access the build configurations.
The list shows a configuration as present, but when I expand...
