hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I have a GSM application connecting to MQTT that worked previously refuse to work when I picked it up again to improve on it.
To make sure there isnt a problem in my firmware...
The following settings are required to make I2S compatible with the AK5720VT.
MCLK=12.288MHz BICK=1.536MHz LRCK=32kHz Bit length=24bit
CONFIG.RATIO >= 2 * CONFIG.SWIDTH...
Hi All,
I have recently design my version 2 of my custom board, everything seems to work on the board, the firmware is fully running but i can't see the BLE device on...
Hi,
I tried to send audio with a sampling frequency of 44100hz, up until this point I had been sending the default sampling frequency of 48000hz.
For this I change the...
Hello,
I am trying to make radio test functions work on my 52840-based board using SDK 2.5.2. After some effort I managed to create a simple test program that partially...
I want to use P0.00 and P0.01 as UART pins. I have shorted the SB3 and SB4, and opened the SB1 and SB2 for using the pin as GPIO.
If I am enabling the " CONFIG_BOOTLOADER_MCUBOOT...
Dear Sirs!
I need that low power comparator on input AN7 reset controller when device is in OFF mode when voltage on pin drop below threshold.
Controller powered +1.8V...
Hi
I have a project base on Nordic sample code "v2.5.0/nrf/samples/cellular/Location" and it fully work with SIM card
now I need to use Onomondo softsim to replace SIM...
Hello, I'm getting these series of events often when the client is sending data to client. This is the the nRF SDK 17.
If I add a delay on the client app that is talking...
Regarding the description key Page 10 of the document "nRF Sniffer for 802.15.4" states "00112233445566778899aabbccddeeff", but does it differ for each device? Also, if there...
Hi there
During updating nRF5340 over bluetooth, really rarely the CPUNet fails to be updated over bluetooth.
The mcuboot says: Image in the secondary slot is not valid...
Hi Team,
I have 1 nRF5340 Audio DK. With the steps mentioned in below links, I configured Json file to Headset and I'm able to achieve it.
Setup Details : Headset - nRF5340...
Hello,
I'm using nrf52840 together with HX711 24bit ADC . My application samples the ADC every 12.5ms (80Hz rate) and the sample is sent out via BLE notification. The HX711...
