Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello
I built the nrf dm sample for the nrf52840dk_nrf52840 target and loaded it on 2 nrf52840 dev kits
Tried both MCPD and RTT methods
No matter what the distance between...
I did some searching through the samples and could not find any that use indications rather than notifications. I did find some references in other posts that are like 8 years...
Has a community member implemented and fabricated the nRF5340 IC in the WLCSP package that has its pad landings spaced at a 350um ?
If so, can you share design guidelines...
Dear community
I'm new to the nRF9160 and to cellular connectivity related functionality.
We're in the concept phase of a product that implements cellular cloud connectivity...
hi team.
i have one doubt.which type of temperature sensor used in nrf52840.you mentioned in nrf52840 data sheet just temperature sensor.but which type it is thermocouples...
Hi,
I have looked at the "mass" example showing how to expose a fatfs via USB MSC, that looks good.
I want to do this, but using the QSPI flash storage.
Is there an...
Hello,
I have a couple of Adafruit Feather nrf52840 express devices and I want to set up a small openthread network. As far as setting up a simple network where all the...
Hi,
Error happens after follow steps:
1. program app.hex+bootloader.hex+device_page.hex+softdevice.hex to boad.
2. use nRF Mesh APP to provision, it runs well
3. add...
I have 2 DK boards neither of which is working.
The first is a PCA10040 V1.2.1. When I plug it into my Window 10 computer with a data cable, Windows says it's an unrecognized...
Hello,
we're developing a NB-IoT application using the nrf9160 and the nrf modem library.
Let’s suppose the modem is in PSM and due to reception/network issues it cannot...
Dear Nordic Team,
on my board with NRF85240 High Voltage mode is used. Accordingly to datasheet (5.3.8.2 Regulator Specifications, REG0 stage), in this mode the following...
Can you help with why I get this serial debug message when trying to start Headset nrf5340_Audio DK in DFU mode
HR [00:00:02.068,450] <err> dfu: SMP_SVR Advertising failed...
Hi!
I have an issue with control of the MAGPIO during RFTEST procedures.
The device is using RF Switch (like Thingy91) and I want to perform SNR/Received signal power...
