Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
Hello,
I'm trying to measure current on my nrf52dk board during a BLE communication. I'm doing that on a nrf52dk board. I connected the power profiler to the board as follows...
Hi Support team,
I'm currently using an nRF5340 DK and an ublox-SARA-R4 modem for MQTT communication, the Zephyr native MQTT lib was used. It can work well. Now I want to...
Hello ,
I'm switching in runtime from battery to USB on my custom nrf52832
On battery ->
bt_mesh_lpn_set enabled bt_mesh_relay_set disabled bt_mesh_friend_set disabled...
The hardware I use is nrf52840Dongle, using nrf_dm sample for development. There are a few problems:
1. I have 8 devices, all within communication range, 4 as base stations...
Hi,
I am running the stock UDP example on a nRF9160-DK (PCA10090, 0.8.5, 2019.7, Modem FW 1.3.6) and the modem crashes immediately.
I have also tried the CoAP example...
Hi,
im use nrf52840 develop my product,and now my pcb is ready,but after some times program, it cant be programmed,also nrf connect and vs code .im try ti recover it by...
Hi
im develop my product base nrfdesktop of ncs,i build the project and program to the nrf52840DK,it can run and perform funcation.but when i program it to my board,it cant...
Hi,
I am trying to connect and acquire the signal from the Adafruit I2S MEMS Microphone using I2s communication with my board (nRF5340 DK). Because I am new in this controller...
This is a continuation of the following ticket: The resolution was logged as DRGN-19197, which was part of v2.4.0 , but did not resolved the issue.
I have created a minimal...
Hello,
Using the sample PSA Protected Storage on the nrf5340 DK with NCS v2.6.1 (and v2.5.2). My prj.conf contains these settings:
I flash the sample provisioning_image...
Hi,
I am using Nordic nRF52833 as a peripheral which uses mcuboot and DFU over BLE. I can easily upgrade firmware on that device by connecting to it with nRF Connect mobile...
Hi,
I use nrf52833 Development board PCA10100 to do loss test as peripheral and speed is 1Mbps, tx power is MAX. It's loss rate is very high, when nrf52833 sends a packet...
Hi, I am trying to use the periodic advertising connection examples and get Hci errors: opcode 0x2036 status 0x01 Failed to create advertising set (err -5)
I am on NCS 2...
Hi:
I checked the zephyr.dts file, but I couldn't find the addresses for interrupt-controller(0x e000e100 ) , timer(0x e000e010) , and memory(0x20000000) in the nRF9160...
With nRF7002DK and TF-M (nrf7002dk_nrf5340_cpuapp_ns.conf) configuration, the sample project works for example.com:
*** Booting nRF Connect SDK v3.5.99-ncs1-1 *** HTTPS...