hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello everyone,
I am designing a Bluetooth repeater that will be powered eather by USB or an embedded Li-Po battery. This device will run with the nRF52833 along with...
Hi,
I am working on a project, where I am trying to create a touch LED project using NRF52832. I have completed the prototype, its working is quite simple. The LED will...
Hello, guys!
We are using nRF51822 SoC with nRF5 SDK v12.3.0 and s130 SoftDevice. One of our desires is to use Software Interrupt (SWI) driver.
However, when I try to...
Hello all,
I am configuring a low power application for the nrf52832 board (custom board). This is a very low power application and I want the board to stay on sleep mode...
Hello everyone, I am working with a BMI160 6-DoF sensor. I have some drivers related to this chip. Using the Segger J-Link debugger the drivers just work fine without any...
I update a couple of device to mfw_nrf9160_1.3.2.zip.
Before that (1.3.1), my experience was to get a ENETDOWN, when calling " sendto" while the device has lost some the...
Hi.
I'm trying to add Bluetooth capability to the "Asset Tracker V2" project. I was able to do it on the nRF9160DK board. I could not find a working example to make the...
Hello,
windows10 x64.
i have used NCS1.9.1 and NCS1.9.99,now i want update to 2.0.99
how to install NCS2.0.99?
because nRF Connect for Desktop Toolchain manager no...
Hi,
1. How to calculate the Flash and RAM usages at runtime? I am able to do it static way but wanted to analyze this at runtime.
2. How to calculate the Heap usages at...
Hallo,
currently I try to optimise the functionality of my extended advertiser code. I found that there are also some call-backs defined for extended advertisers. The struct...
I use iOS nRF Connect APP to test DFU. But it failed with writing is not permitted.
The following is log message of nRF52832 device. 00> <info> app: Inside main 00> 00>...
Hi,
I am working on a system that runs a proprietary protocol, i.e. non-BLE, which works fine when it uses either uncoded links or S=8 ( LR125Kbit ) coded links, but I want...
Hello everyone, I am trying to send a string printed float number using the ESB protocol. I am using nrfConnect SDK 1.9.1 with nrf52832, started off with the supplied esb_ptx...
Respected,
I am using NRF connect for desktop for programming my actinius sensor (ICARUS IOT BOARD) but whenever I want to upload and reset the board using actinius programmer...
