hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
problem description:
hi, I just got a PCA10040 development board with which I plan to learn about nrf connect SDK.
so I try the common BLE peripheral demo,but I 've met...
In order to add the BLE DFU service, I need to increase the GATT table size and therefore memory as mentioned here: .
However, when I tried to increase the file ble_app_uart_gcc_nrf52...
Try by changing the RAM size but it didn't worked.
<info> app_timer: RTC: initialized. <error> app: ERROR 4 [NRF_ERROR_NO_MEM] at :0 PC at: 0x00000000 <error> app: End of...
Hello, I have managed to get two NRF5340DK linked and measured their throughput. Now I need to change their Output Radio Amplifier Power to test again. And then I also need...
Hello Nordic Team,
I have an issue on one of my 10056 DK. The DK is connected to a development PC, appears in device manager as a Jlink CDC UART port, and as a mass storage...
In the Zigbee framework, what is the purpose of the return variable from zb_osif_sleep() ? The "documentation" for Zigbee seems to implement a "guess and figure it out for...
Hi,
I'm following the ble_template example on my custom board. I'm having an issue with waking up (soft reset) the device from sd_power_system_off. I can power off the system...
Hi ,
We are using s140_nrf52_6.0.0_softdevice, SDK 15.0.0 for NRF52840 chip. Does this sdk and soft device supports extended advertisement?
I could able to enable this...
I use both nrf52833 boards to do AOA test.But i use thr antenna array board of silab.The board are 16 antennas.I use the NCS version 1.9.1.
The next is my device stcture...
Hey All:
I'm trying to create a new app in VS Code. I've got the latest v2.0.0 SDK. I get the following error:
[west]: FATAL ERROR: Malformed manifest file: /home/ebolton...
hi support team,
customer have one question about nrf dfu with serial:" how to disable flow control for 2 wire uart".
previously we have one ticket :"https://devzone.nordicsemi...
Hi,
I'm using nrf52832 DK with SPI slave mode to read 600 bytes from other nrf52832 DK with SPI master mode but i can't receive more than 255 bytes buffer.
If you know...
Hi everyone,
My project consists on a nrf5340dk working as a peripheal UART, i set the advertisment to coded phy like this:
Setting the child image as hr_coded for be...
Hi,
I want to buy a nRF5340-DK.
This is the image of the official Nordic web page https://www.nordicsemi.com/Products/Development-hardware/nrf5340-dk
It appears that...
