There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
I use Nordic BLE Mesh example(Light Switch), I want to implement remote control. The following is the topology map, and the publish & subscribe address(Group address) has...
Using a NRF9160DK. SDK2.0.0. Modem 1.3.2.
I have a problem when setting up a new NRF board to run with MQTT with AWS.
When the setup is running, I get LOG <inf> for...
Hi,
we have a unit that needs to go for conformance testing.
The only external interface we have is the nNR52833s USB port (pins 12/13 on QDAA).
Alternatively can the...
Hello,
We're using a nRF52840 with S140 SoftDevice (v7.3.0) for a Central device but we're having a disturbing issue when scanning: a hardfault occurs less than 2 seconds...
Using the pc_ble_driver_py.ble_driver I'm able to subscribe to notifications, but unable to get the values upon connection. The error is:
I do not know how to install...
We have an application where we need the PWM pin state to revert to high impedance between bursts. It doesn't appear this behavior is capable by default. Is there a means...
Hi,
As mentioned in the question, I want to use the external clock as the RTC instead of the internal clock. How to configure it?
Platform: Windows 10
NCS version: 1...
For a fully connected set of node devices in a BLE mesh network, where any node device can send data packets to any other node device via an optimally short number of radio...
Hey,
upon a BLE_GAP_EVT_ADV_REPORT I call the following function:
static void pass_adv_data(ble_gap_evt_adv_report_t const *p_adv_report).
The function checks the p_adv_report...
Hello,
I'm having trouble setting up CMSIS Configuration Wizard in SES IDE v5.50a on Mac OS.
I've followed the instruction in https://www.youtube.com/watch?v=b0MxWaAjMco...
hi Team,
working Environment:
nrf52832 DK, SDK 17.1.0, keil IDE uvision 5, Windows 10 pro.
i am working with ble_peripheral based ble_app_uart example.
this program...
I am working on some teching modules covering MCUBoot and DFU ... and trying to get the
basic examples built for an nRF52840 DK board ... and am running into an error along...
Hi,
i am using MCUBOOT + nrF5340 and i am using the nRF Connect Device Manager to upload firmware and perform the upgrade.
I would like to know if it is possible to execute...
How do I check to see if a peripheral is inside the list of bonded units of a central?
I know I can just scan -> see unit -> connect -> change security and if it IS bonded...
